Manuals / Honeywell / Household Appliance / Thermostat

Honeywell SDC manual 30 C

Models: SDC

1 64

Download 64 pages 29.07 Kb

Page 53

SDC / DHC	Operation

4.2.3.3.1Individualised daytime room temperature for each heating circuit

Setting ► Press ¥ button.

C

►Select desired heating circuit (HC, MC-1 or MC-2) by turning the input button î.

►Confirm selected circuit by pressing the input button î.

►Set flashing room temperature specification to the desired value by turning the input button î.

►Confirm set value by pressing the ¥ button.

Alternative: Automatic acceptance of the value after the set information time (see 4.1.2.7 "System information" button, pg. 26).

Setting range	5 ... 30 °C
Factory setting	20 °C

4.2.3.3.2Individualised night-time room temperature for each heating circuit

Setting ► Press ¦ button.

C

►Select desired heating circuit (HC, MC-1 or MC-2) by turning the input button î.

►Confirm selected circuit by pressing the input button î.

►Set flashing room temperature specification to the desired value by turning the input button î.

►Confirm set value by pressing the ¦ button.

Alternative: Automatic acceptance of the value after the set information time (see 4.1.2.7 "System information" button, pg. 26).

Setting range	5 ... 30 °C
Factory setting	16 °C

EN2H-0220GE51 R0308

53

Image 53

Honeywell SDC manual 30 C

Contents

Heating Controller SDC Remote Heating Controller DHC EN2H-0220GE51 R0308 Contents Log ContentsSDC / DHC Page Intended use Software versionCable installation Power supplyConnection conditions Cable cross-sectionsGrounding and zeroing Hot-water temperature greater than 60 CSDC / DHC SDC 12-31 TypeBurnerstage 2 or Districtheating valve Closed Display and operating elements OperationDisplay basic display Factory setting Daytime room temperature buttonSetting range Operating elements Input button press / turnSetting Night-time room temperature buttonDaytime hot-water temperature button Factory setting 50 COperating mode button basic display Absent Absence mode short-term program 2.5.1 Setting ApplicationP1 P2, P3 Party mode short-term programAutomatic mode Disabling / enabling default programs P2 to P3 Display Disabling / enabling default program P2 to P3Enabling Manual summer operation excluding heating operationContinuous lowering operation Continuous heating operationSwitching time programs / Holiday programs button Standby modeHoliday mode Factory setting Current date System information button Operating overview Manual mode / Emission measurement button Setting range Factory settingCancellation 2.9 Setting Setting range Heating curve Menu-selection level Menu functions are described in the following Returning AccessTime Date menu Timeprograms menu Access Returning Selection of day of the week and cycle Selection of the control circuitSelection of the program Switch-off time Cycle temperature DHW Switching time programming programs P2 and P3 disabledDefault program P1 Default switching time program P1 for heating and hot waterSwitching time programming program P2 and P3 enabled Default program P3 Default program P2Calling up the copy function days Copying switching time programs days Source day Target dayCalling up the copy function heating circuits Block programming SDC / DHC Copying heating circuits Reloading default programs SDC / DHC Reloading default programs Switching time programs P2 and P3 enabled Setting values DE System Parameters menu Access ReturningFactory setting German Language selectionSet values Operating mode Setting range Set valuesTime program 30 C Summer / Heating limit Quick increase in outside temperatureSlow increase in outside temperature Undoing deactivation Factory setting 20 CParameter reset DHW menu Night-time hot-water temperatureFactory setting 40 C Set values RED lowering operation Reduced operationHeating system ECO switch-off operationRadiator systems Time Setpoint Opt Wed Cont. circuit Thu Fri Sat Sun LogSDC / DHC SDC / DHC Page Automation and Control Solutions