Honeywell 2-Partitioned Security System Partition-Specific Fields, Partition # Program Fields

Partition-Specific Fields

(Duplicate this page for each partition in the installation.) To program these fields,

1.Press *91 to select a partition.

2.Enter a partition-specific field number (ex. *09).

3.Make the required entry.

4.Repeat steps 1-3 for the other partition in the system.

PARTITION #____ PROGRAM FIELDS

1st Page Fields
*09	ENTRY DELAY #1	[02]
	00, 02-15 times 15 seconds.
	Maximum 03 for UL Listed installations.
*10	EXIT DELAY #1	[04]

*88 BURG. ALARM COMM. DELAY [0]

1=16 seconds; 0=no delay. Must be "0" for UL installations.

*90 SEC. SUBS. ACCT #
Enter 00-09; B-F (11-15)	[15 15 15 15]

2nd Page Fields

00, 03-15 times 15 seconds.

Maximum 04 for UL Listed installations.

*11	ENTRY DELAY #2	[06]
	00, 02-15 times 15 seconds.
	Maximum 03 for UL installations.
*12	EXIT DELAY #2	[08]
	00, 03-15 times 15 seconds.
	Maximum 04 for UL installations.
*13	ALARM SOUNDER DURATION	[04]
	01-15 times 2 minutes.
	Must be minimum 16 minutes for UL installations.
*16	CONFIRMATION OF ARMING DING	[0]
	1=enable; 0=disable.
	Must be "1" for UL installations.
*22	KEYPAD PANIC ENABLES [001]
	1=enable; 0=disable	995 996	999
*23	MULTIPLE ALARMS	[1]

1=yes; 0=no. Must be 1 for UL installations.

1*43 PERM. KEYPAD BACKLIGHT	[0]
1=enable; 0=disable When disabled, display lights when
any key is pressed, and turns off after period of keypad
inactivity.

1*45	EXIT DELAY SOUNDING	[0]
	1=enable; 0=disable. Produces quick beeping during exit
	delay if enabled.
1*47	CHIME ON BELL 1	[0]
	1=enable; 0=disable
1*52	SEND CANCEL IF ALARM + OFF	[0]
	1=no restriction; 0=within Bell Timeout period only
1*76	ACCESS CONTROL RELAY FOR PART.[00]

Relay will be pulsed for 2 seconds whenever code + [0] is pressed. Enter 00-08; 00=none. Must be "00" for UL installs.

3rd Page Fields

2*18 ENABLE GOTO FOR THIS PARTITION [0]

1=Allow log-on from other partitions; 0=disable

*29 QUICK ARM [1]

1=yes; 0=no

2*20 ENABLE J7 TRIGGERS BY PARTITION [1]

0=disable; 1=enable for

*32	PRIM. SUBS. ACCT #
	Enter 00-09; B-F (11-15)	[15 15 15	15]
*38	PREVENT ZONE XX BYPASS			[00]
	001-64; 000 if all zones can be bypassed
*39	ENABLE OPEN/CLOSE REPORT				[1]
	FOR INSTALLER CODE
	1=enable; 0=disable
*84	SWINGER SUPPRESSION			[03]

01-15 alarms; Must be "00" (disabled) for UL installations.

*85 ENABLE DIALER REPORTS FOR PANICS & DURESS

1=enable; [0=disable]

995 996 999 Duress

*87 ENTRY WARNING [1]

1=continuous; 0=3 beeps

SUMMARY OF PROGRAMMING COMMANDS

•To enter program mode, enter installer code + [8] + [0] + [0]

•To set standard defaults, press *97

•To change to next page of program fields, press *94

•To return to previous set of fields, press *99

•To erase account and phone number field entries, press [*] + field number + [*]

•To assign zone descriptors, press #93 + follow menu prompts

•To add custom words, press #93 + follow menu prompts

•To enter Installer's Message, press #93 + follow menu prompts

•To exit program mode, enter *99 OR *98: *99 allows re- access to programming mode by installer code. *98 prevents re-access to programming mode by installer code.

– 9 –