Manuals / Hoshizaki / Kitchen Appliance / Refrigerator

Hoshizaki KML-250MAH, MWH Remote Models MRH, Side, Rear, Model Shown KML-631MRH, Bottom

Models: MWH KML-351MAH KML-250MAH MWH KML-631MAH MWH MRH MWH KML-451MAH

1 40

Download 40 pages 33.48 Kb

Page 10

Image 10

3. Remote Models (MRH)

Units: mm [in.]

Side		Rear
Model Shown: KML-631MRH
KML-631MRH		Model Shown: KML-631MRH
A 659 [26]		Model Shown: KML-631MRH
A 659 [26]
B 615 [24-1/4]		Bottom
C 605 [23-7/8]		Bottom
C 605 [23-7/8]
D 448 [17-5/8]
E 41	[1-5/8]
F 63	[2-1/2]
G 75	[3]
NOTICE		Model Shown: KML-631MRH

•Allow 6" (15 cm) clearance at rear, sides, and top for proper air circulation and ease of maintenance and/or service should they be required.

•The ice storage bin opening must match the bottom opening as in the illustration.

Page 10

Image 10

Hoshizaki KML-250MAH, MWH KML-451MAH, MWH KML-631MAH Remote Models MRH, Side, Rear, Model Shown KML-631MRH, Bottom

Contents

“A Superior Degree of Reliability” IssuedLow-ProfileModular Crescent Cuber HoshizakiHoshizaki America, IncPeachtree City, GA Complete and detailed explanation of the problemHOSHIZAKI AMERICA, INC 618 Highway 74 South Attn Hoshizaki Technical Support DepartmentCONTENTS appliance or property Important Safety Informationserious injury care of the applianceWARNING, continued Additional Warning for Remote Models1. KML-250M H I. SpecificationsA. Electrical and Refrigerant Data 2. KML-351M HModel Number 3. KML-451M H4. KML-631M H KML-451MAH1. Air-CooledModels MAH B. Dimensions/ConnectionsUnits mm in 2. Water-CooledModels MWH Rear 3. Remote Models MRHSide Model Shown KML-631MRHIcemaker Units mm inURC-9FHeat of Rejection AT 90F 32CB. Checks Before Installation II. Installation and Operating InstructionsA. Location C. How to Remove Panels See Fig Fig. 2a D. SetupFig. 2b Intentionally Left Blank For All Models E. Electrical ConnectionAdditional Warnings for Remote Models JUNCTION BOX ELECTRICAL CONNECTION115-120/60/1 BROWNF. Water Supply and Drain Connections See Figs. 4 throughFig. 4 Air-Cooledand Remote Models 1. Icemaker2. Water-CooledCondenser a KML-250/351/451MWH Connection to an Open Drain SystemWater-CooledModels 1 Connection to an Open Drain SystemWater-CooledModels Connection to a Closed Loop System2 Connection to a Closed Loop System Water-CooledModels Connection to an Open Drain Systemb KML-631MWH 1 Connection to an Open Drain SystemConnection to a Closed Loop System 2 Connection to a Closed Loop SystemWater-CooledModels Minimum water flow to the condenser is 4 GPMG. Installation of Remote Condenser Unit 1.Location3.Setup 2.Checks Before Installation4. Line Set Size and Refrigerant Charge aFactory Line Set Installation 5. Line Set Installation1Factory Line Set Modification bField Fabricated Line Set Installation DO NOT USE THREAD SEALANT Remote Condenser UnitMale Fitting After Tight, Tighten an Additional 1/6 Turn6. Electrical Connection 7.Stacking Remote Condenser Unit H. Final Checklist I. Startup Additional Notice for Remote ModelsIII. Maintenance A.Maintenance ScheduleB. Cleaning and Sanitizing Instructions 1. Cleaning Procedure9Pour the cleaning solution into the water tank 9Move the service switch to the DRAIN position 4Move the service switch to the WASH position7Turn off the power supply after 15 minutes 11Turn off the power supplyIV. Preparing the Icemaker for Periods of Non-Use 2.Drain the water tank6Close the drain valves V. Disposal HOSHIZAKI AMERICA, INC

3. Remote Models (MRH)

Side

Model Shown: KML-631MRH

Bottom