Manuals / Hoshizaki / Kitchen Appliance / Refrigerator

Hoshizaki MWH KML-351MAH, MRH Units mm in, URC-9FHeat of Rejection, Icemaker, AT 90F 32C, Model

Models: MWH KML-351MAH KML-250MAH MWH KML-631MAH MWH MRH MWH KML-451MAH

1 40

Download 40 pages 33.48 Kb

Page 11

Image 11

4. Remote Condenser Unit URC-9F (use with KML-631MRH)

Units: mm [in.]

NOTICE

Allow 24" (61 cm) clearance at front and rear for proper air circulation and ease of maintenance and/or service should they be required.

	URC-9F Heat of Rejection
Icemaker	AT 90°F (32°C)
Model	WT 70°F (21°C)
KML-631MRH	10,300 BTU/hr

Top

Rear

Page 11

Image 11

Hoshizaki MWH KML-351MAH Units mm in, URC-9FHeat of Rejection, Icemaker, AT 90F 32C, Model, WT 70F 21C, KML-631MRH

Contents

HoshizakiHoshizaki America, Inc IssuedLow-ProfileModular Crescent Cuber “A Superior Degree of Reliability”Attn Hoshizaki Technical Support Department Complete and detailed explanation of the problemHOSHIZAKI AMERICA, INC 618 Highway 74 South Peachtree City, GACONTENTS care of the appliance Important Safety Informationserious injury appliance or propertyAdditional Warning for Remote Models WARNING, continued2. KML-351M H I. SpecificationsA. Electrical and Refrigerant Data 1. KML-250M HKML-451MAH 3. KML-451M H4. KML-631M H Model NumberUnits mm in B. Dimensions/Connections1. Air-CooledModels MAH 2. Water-CooledModels MWH Model Shown KML-631MRH 3. Remote Models MRHSide RearAT 90F 32C Units mm inURC-9FHeat of Rejection IcemakerA. Location II. Installation and Operating InstructionsB. Checks Before Installation C. How to Remove Panels See Fig Fig. 2b D. SetupFig. 2a Intentionally Left Blank Additional Warnings for Remote Models E. Electrical ConnectionFor All Models BROWN ELECTRICAL CONNECTION115-120/60/1 JUNCTION BOXSee Figs. 4 through F. Water Supply and Drain Connections1. Icemaker Fig. 4 Air-Cooledand Remote Models1 Connection to an Open Drain System Connection to an Open Drain SystemWater-CooledModels 2. Water-CooledCondenser a KML-250/351/451MWH2 Connection to a Closed Loop System Connection to a Closed Loop SystemWater-CooledModels 1 Connection to an Open Drain System Connection to an Open Drain Systemb KML-631MWH Water-CooledModelsMinimum water flow to the condenser is 4 GPM 2 Connection to a Closed Loop SystemWater-CooledModels Connection to a Closed Loop System1.Location G. Installation of Remote Condenser Unit4. Line Set Size and Refrigerant Charge 2.Checks Before Installation3.Setup 1Factory Line Set Modification 5. Line Set InstallationaFactory Line Set Installation bField Fabricated Line Set Installation After Tight, Tighten an Additional 1/6 Turn Remote Condenser UnitMale Fitting DO NOT USE THREAD SEALANT6. Electrical Connection 7.Stacking Remote Condenser Unit H. Final Checklist Additional Notice for Remote Models I. StartupA.Maintenance Schedule III. Maintenance1. Cleaning Procedure B. Cleaning and Sanitizing Instructions9Pour the cleaning solution into the water tank 11Turn off the power supply 4Move the service switch to the WASH position7Turn off the power supply after 15 minutes 9Move the service switch to the DRAIN position2.Drain the water tank IV. Preparing the Icemaker for Periods of Non-Use6Close the drain valves V. Disposal HOSHIZAKI AMERICA, INC

URC-9F Heat of Rejection

Icemaker

AT 90°F (32°C)

Model

WT 70°F (21°C)

10,300 BTU/hr

Top