Manuals / Hoshizaki / Kitchen Appliance / Refrigerator

Hoshizaki MWH KML-451MAH, MRH B. Dimensions/Connections, Air-CooledModels MAH, Units mm in

Models: MWH KML-351MAH KML-250MAH MWH KML-631MAH MWH MRH MWH KML-451MAH

1 40

Download 40 pages 33.48 Kb

Page 8

B. Dimensions/Connections

B. Dimensions/Connections

1. Air-Cooled Models (MAH)

Units: mm [in.]

Side

Model Shown: KML-451MAH

KML-250MAH KML-631MAH

KML-351MAH

KML-451MAH

A 559	[22]	659	[26]
B 515 [20-1/4]		615 [24-1/4]
C 505	[19-7/8]	605	[23-7/8]

NOTICE

•Allow 6" (15 cm) clearance at rear, sides, and top for proper air circulation and ease of maintenance and/or service should they be required.

•The ice storage bin opening must match the bottom opening as in the illustration.

Rear

Model Shown: KML-451MAH

Bottom

Model Shown: KML-451MAH

8

Image 8

Hoshizaki MWH KML-451MAH, MRH, MWH KML-631MAH, KML-250MAH B. Dimensions/Connections, Air-CooledModels MAH, Units mm in

Contents

Issued Low-ProfileModular Crescent Cuber“A Superior Degree of Reliability” HoshizakiHoshizaki America, IncComplete and detailed explanation of the problem HOSHIZAKI AMERICA, INC 618 Highway 74 SouthPeachtree City, GA Attn Hoshizaki Technical Support DepartmentCONTENTS Important Safety Information serious injuryappliance or property care of the applianceWARNING, continued Additional Warning for Remote ModelsI. Specifications A. Electrical and Refrigerant Data1. KML-250M H 2. KML-351M H3. KML-451M H 4. KML-631M HModel Number KML-451MAHUnits mm in B. Dimensions/Connections1. Air-CooledModels MAH 2. Water-CooledModels MWH 3. Remote Models MRH SideRear Model Shown KML-631MRHUnits mm in URC-9FHeat of RejectionIcemaker AT 90F 32CA. Location II. Installation and Operating InstructionsB. Checks Before Installation C. How to Remove Panels See Fig Fig. 2b D. SetupFig. 2a Intentionally Left Blank Additional Warnings for Remote Models E. Electrical ConnectionFor All Models ELECTRICAL CONNECTION 115-120/60/1JUNCTION BOX BROWNF. Water Supply and Drain Connections See Figs. 4 throughFig. 4 Air-Cooledand Remote Models 1. IcemakerConnection to an Open Drain System Water-CooledModels2. Water-CooledCondenser a KML-250/351/451MWH 1 Connection to an Open Drain System2 Connection to a Closed Loop System Connection to a Closed Loop SystemWater-CooledModels Connection to an Open Drain System b KML-631MWHWater-CooledModels 1 Connection to an Open Drain System2 Connection to a Closed Loop System Water-CooledModelsConnection to a Closed Loop System Minimum water flow to the condenser is 4 GPMG. Installation of Remote Condenser Unit 1.Location4. Line Set Size and Refrigerant Charge 2.Checks Before Installation3.Setup 1Factory Line Set Modification 5. Line Set InstallationaFactory Line Set Installation bField Fabricated Line Set Installation Remote Condenser Unit Male FittingDO NOT USE THREAD SEALANT After Tight, Tighten an Additional 1/6 Turn6. Electrical Connection 7.Stacking Remote Condenser Unit H. Final Checklist I. Startup Additional Notice for Remote ModelsIII. Maintenance A.Maintenance ScheduleB. Cleaning and Sanitizing Instructions 1. Cleaning Procedure9Pour the cleaning solution into the water tank 4Move the service switch to the WASH position 7Turn off the power supply after 15 minutes9Move the service switch to the DRAIN position 11Turn off the power supplyIV. Preparing the Icemaker for Periods of Non-Use 2.Drain the water tank6Close the drain valves V. Disposal HOSHIZAKI AMERICA, INC