Manuals / Brands / Power Tools / Router / HP / Power Tools / Router

HP 7000 dl Router Supplying Power to the Unit, Supplying Redundant Power to the Unit, Instructions for Connecting the RPS

1 80

Download 80 pages, 3.06 Mb

ProCurve Secure Router Installation Guide	Unit Installation

Supplying Power to the Unit

After installing the base unit and any option modules, the ProCurve Secure Router is ready to be powered- up. To power the unit, ensure that the unit is properly connected to an appropriate power source (see the sections below).

The ProCurve Secure Router comes equipped with an auto-ranging power supply rated as follows:

•ProCurve Secure Router 7102dl: 100 to 127 VAC, 0.4 A/200 to 240 VAC, 0.2 A, 50 to 60 Hz

•ProCurve Secure Router 7203dl: 100 to 127 VAC, 0.8 A/200 to 240 VAC, 0.4 A, 50 to 60 Hz

Agrounded, three-plug detachable cable is included with the shipment.

Caution Maximum recommended ambient operating temperature is 50°C (122°F).

Supplying Redundant Power to the Unit

A redundant power supply (RPS) is only available with the ProCurve Secure Router 7203dl. Follow these instructions when connecting the RPS.

Instructions for Connecting the RPS

1Remove the blank cover plate from the RPS slot on the back of the ProCurve Secure Router 7203dl.

2Plug the RPS power cable (with the HP logo on the connector facing up) into this slot. (The RPS power cable comes attached to the HP 600 RPS/EPS. The cable is 1.25 meters [4.1 feet] long.) For more information about connecting the RPS, refer to the ProCurve 600 Redundant and External Power Supply Installation and Getting Started Guide.

3Secure the screws.

Your ProCurve Secure Router is now ready to be configured and connected to the network. For more information on configuring a specific application, refer to the quick configuration documents provided on your ProCurve SROS Documentation CD. For details on the CLI, refer to the SROS Command Line Interface Reference Guide (also included on your CD).

5990-3760

Copyright 2006 Hewlett-Packard Development Company, LP

41

Contents

Page Page Page Copyright Trademarks Software Licensing Agreement Disclaimer Warranty Table of Contents Page List of Figures List of Tables 1.INTRODUCTION TO THE PROCURVE SECURE ROUTER ProCurve Secure Router 7102dl ProCurve Secure Router 7203dl Features Specifications Unpack and Inspect the System Contents of Shipments Page Note Caution 2.PHYSICAL DESCRIPTION Reviewing the Front Panel Design Front Panel Switches, Interfaces, and LEDs Table 1. ProCurve Secure Router LEDs (Continued) Console Interface 10/100BaseT Ethernet Interface and Activity LEDs Eth 0/1, Eth 0/2 Module Card Slots Reviewing the Rear Panel Design Rear Panel Interfaces 3.OPTION MODULES Interface Modules 1xT1 Interface Module 1xT1 + DSX-1Interface Module 2xT1 Interface Module 1xE1 Interface Module 1xE1 + G.703 Drop and Insert Interface Module 2xE1 Interface Module 1xSerial Interface Module 1xADSL2+ Annex A Interface Module 1xADSL2+ Annex B Interface Module 2xISDN BRI S/T Interface Module 2xISDN BRI U Interface Module 8xT1/E1 Wide Module Page 8xSerial Wide Module Backup Modules ISDN BRI U Backup Module ISDN S/T Backup Module Analog Modem Backup Module 4.UNIT INSTALLATION Tools Required Mounting Options Rack Mounting ProCurve Secure Router Grounding the Router Grounding Requirements Statement Installing Interface and Backup Modules Instructions for Installing the Backup Module Figure 19. Installing Backup Module and Interface Module Instructions for Installing the Interface Modules and Wide Modules Installing the Encryption Module Installing a CompactFlash® Card T1/E1 Mode Dip-Switch Supplying Power to the Unit Supplying Redundant Power to the Unit Page APPENDIX A. CONNECTOR PIN DEFINITIONS Base Unit Pinouts Interface Module and Wide Module Pinouts Table A-6.G.703 Connector Pinouts Table A-7.1xSerial Interface and 8xSerial Wide Module Connector Pinouts Page Backup Connectors Page APPENDIX B. SAFETY AND REGULATORY INFORMATION ESD Precautions Safety Information (English) Safety Instructions Grounding Servicing Accessories Regulatory Model Identification Number Conserver ces instructions de sécurité Informations concernant la sécurité (French) Page Hinweise zur Sicherheit (German) Page Conservare queste importanti istruzioni sulla sicurezza Informationi sulla sicurezza (Italian) Page Conservar estas Instrucciones de seguridad Importantes Consideraciones sobre la seguridad (Spanish) Page Safety Information (Japan) Safety Information (China) FCC Radio Frequency Interference Statement for United States Electromagnetic Compatibility (EMC) Table Page Industry Canada Compliance Information Canadian Emissions Requirements Notice for European Union Notice for France Notice for Japan Notice for Korea FCC-RequiredInformation Declaration of Conformity (USA) Declaration of Conformity (European) Warranty and Customer Service Installation and Maintenance Support Page APPENDIX C. WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) INSTRUCTIONS Page Page Page Index Numerics