Configure the serial connection | HP Client Bridge M111 specs

Getting started

Scenario 3: Connecting a serial device to a wireless network

Configuration procedure

The initial configuration steps for this scenario are the same as for Scenario 1. For each step see the instructions on the indicated page.

A. Configure your computer

See Configure your computer on page 2-3.

B. Connect to the M111

See Connect to the M111 on page 2-4.

C. Start the M111

See Start the M111 on page 2-4.

D. Connect to the management tool and login

See Connect to the management tool and login on page 2-4.

E. Set the M111 IP address

See Set the M111 IP address on page 2-5.

F.Configure a station profile

See Configure a station profile on page 2-6.

G. Configure the serial connection

1.Connect the serial device to the serial port on the M111 using a straight-through serial cable. (For serial port specifications, see Serial port connector on page 3-24.)

2.Select Network > TCP Serial. The TCP to serial configuration page opens.

2-12

Image 28

HP Client Bridge M111 manual Configure the serial connection

Contents

ProCurve 5400zl Switches HP ProCurve M111 Client Bridge Page HP ProCurve M111 Client Bridge Publication Number Contents Working with the M111 Field descriptions To assign a management address Resetting to factory defaults Regulatory information Viii Introduction About this guide Products coveredImportant terms Conventions Commands and program listings Example Description Key features Introducing the M111 Client Bridge Professional Installation Required Safety informationServicing Online documentation HP ProCurve Networking supportBefore contacting support Getting started Deploying the M111 Scenario 1 Connecting wired devices to a wireless networkOverview Configuration procedure Configure your computer Connect to the M111 Passwords Select Network DNS Configure a station profile Connect the wired computers to the M111  The printer is configured with a static IP address Configure MAC cloning options Connect the wired device to the M111 Scenario 3 Connecting a serial device to a wireless network Configure the serial connection Getting started Getting started Working with the M111 802.1X certificates Certificate stores Certificate usage Management tool About passwordsStarting the management tool Customizing management tool settings Manager and Operator accounts Passwords Security policies Security Web server IP address configurationAuto-refresh To configure IP addressing Radio configuration Wireless range Wireless mode To configure the radioRestrict channels to Antenna selection Fast roaming threshold Fast roaming delta threshold Scan channel delay Fast scan channel delayFast roaming threshold count Minimum SNR threshold Using station profiles to establish a wireless link Advanced wireless settingsTransmit power control RTS threshold Working with the M111 To add or edit a station profile General Wireless security Wireless protectionKey source EAP method Working with the M111 Quality of service Viewing APs in the neighborhoodEncryption type Ap1certificate or ap2certificate Access category Configuring Quality of Service QoSField descriptions Priority mechanisms QoS settings in a station profile802.1p Differentiated Services DiffServ Very-high, high, normal, low priority Disabled Creating IP QoS profilesTo define an IP QoS profile Upstream DiffServ tagging Connecting serial devices SettingsProfile name Protocol Start port/ End port Serial port connector To connect a serial device Transmit timeout Idle timeoutMode Remote IP address Drop wireless link when port 1 is connected Data bitsParity bit Stop bits DNS configuration Connection timeTx kbytes Rx kbytes DNS switch on server failure Dynamically assigned DNS serversOverride dynamically assigned DNS servers Server DNS switch over Enable the Redirect unsupported traffic to optionHandling unsupported traffic To forward unsupported traffic IP forwarding Cloning the address of a wired deviceLimitations Wireless access to the M111 when MAC cloning is active Enabling Ethernet MAC cloning Setting up management traffic interception Management tool TCP portSnmp agent UDP port Select Management Snmp Using filters to restrict wireless traffic Enable the Wireless traffic filters optionSnmp notifications UDP port Remote log UDP port Assigning a management address To assign a management address Snmp V1/v2c communities AttributesV3 users Managing certificates Notification receivers 802.1X Install TLS client certificate PasswordInstall 802.1X certificates Certificate stores 802.1X Manage TLS client certificates802.1X Trusted CA certificates 802.1X Manage CA certificates Trusted CA certificate store Installing a new CA certificateCA certificate import formats Certificate and private key store END Certificate Specify the Pkcs #12 password Default installed private key/public key certificate chainsCertificate usage Changing the certificate assigned to a service About certificate warnings Manual configuration file management Configuration file managementBackup configuration Restore configuration Reset configurationScheduled operations Software updates Performing an immediate software update Performing a scheduled updateSelect Install Enable Scheduled install Working with the M111 Regulatory information Manufacturers FCC Declaration of Conformity Statement Countries of Operation & Conditions of Use Operation Using 5 GHz Channels in the European Community GHz Operation Supported External Antennas 5470Indoor or outdoor use 1000 124, 128, 132, 136 Antenna Band GHz DGT LPD Low Power Device Statement Resetting to factory defaults Using the management tool Using the Reset buttonHow it works Page Technology for better business outcomes