Customer Service, Your Comments Are Requested | HP FlexJet E

60 Ioline FlexJet E User Guide

prevent damage. Seal the container and note the RMA number near the address block.

3.Ship the container using FED-EX or another approved carrier. COD shipments ARE NOT ACCEPTED. An Ioline representa- tive will contact you prior to the start of work with an estimate of repair cost. All repairs are warranted for 90 days.

Customer Service

Ioline Corporation is committed to providing quality service and support to our customers. If you need assistance with an Ioline prod- uct, contact your local dealer or Ioline authorized service center. You may also contact:

Ioline Customer Service Department

Monday through Friday

7:00 A.M. - 5:00 P.M. U.S. Pacific Time

Voice: 1.425.398.8282

Fax: 1.425.398.8383

support@ioline.com

www.ioline.com

Your Comments

Are Requested

Ioline Corporation is interested in comments on our documentation and products. Please send corrections or suggestions to:

Ioline Corporation

14140 NE 200th Street

Woodinville,WA 98072 USA

Voice: 1.425.398.8282

Fax: 1.425.398.8383

info@ioline.com

www.ioline.com

This User Guide is provided for informational purposes only. The contents are subject to change without notice, and Ioline Corpora- tion assumes no responsibility for any errors that are contained herein. No part of this User Guide may be copied, disseminated, or distributed without the express written consent of Ioline Corpora- tion.

Image 58

HP FlexJet E, StudioJet manual Customer Service, Your Comments Are Requested, 700 A.M. 500 P.M. U.S. Pacific Time

Contents

User Guide User Notice Ioline Flexjet E Printers Table of Contents Routine Maintenance Glossary Index Page Page Safety & Cautions Visual Reference Guide KM N AB C D E F Chapter Getting Started How The Ioline FlexJet E and StudioJet printers Work Ioline FlexJet E User Guide Assembling the Stand Printer AssemblyUnpacking the Printer Attaching the Printer to the Stand Cable Connections Serial ConfigurationCOM Port Installation Other Serial Port SettingsSoftware Setup Options Baud Rate CAD Power On Installing FlexPlot and the Control Center This page intentionally left blank Keypad Controls Start/Stop Quality CleanSet Origin Special Key Combinations Control Center Changing System SettingsVariety of settings are adjustable to fit specific needs Overview Communications Control Center Menu Bar FeaturesFile Tools Control Center Menu Options Consumables General Guidelines Printing a MarkerSend marker/plot files Loading Paper on the StudioJet Loading Paper on the FlexJet E Installing the Take-up Shaft FlexJet E only Feeding Paper 2H+ FlexJet E Tape Paper to theTake-up Shaft Positioning the Pinchwheels Insert Front Dancer Bar Positioning the pinchwheels Set an Origin Pausing a Marker PlotInsert Rear Dancer Bar2H+ FJE Models Only Sending Plot Files Canceling a Marker Plot Removing Markers from the Take-up Shaft Manually Freeing Take-up Shaft Manually freeing the take-up shaft Automatically Freeing the Take-Up Shaft Reattach Paper To the Take-up Shaft Printing to the Floor Cleaning the Drive Shaft Cleaning the Platen and Traverse Size Calibration Cleaning the Support BlocksPrepare the Printer See the Operation chapter Use the Control Center to Gather the Calibration Data Click on Done when finished Routine MaintenanceEnter the Calibration Data Cartridge Calibration Prepare the Printer Click on Done when finished Motion Adjust Carriage Scan AlignmentFrame Gap Paper Scan Alignment Automatic Cleaning Procedure Cartridge Maintenance and HandlingCheck Cartridges Soft, fiberless, and moistened with deionized water Manual Cleaning ProcedureOpen the latch for the first cartridge and remove it Print Cartridge Storage Update the Firmware Reset Calibration Values General Troubleshooting Media Tracking Line Quality Printing QualitySerial Communication Keypad Error Codes Troubleshooting Common Issues Printer does not complete the marker Cause Quick Start Guide to level Regular or intermittent paper tearing Cause FlexJet E Models only This page intentionally left blank Service & Support Getting Help Your Comments Are Requested Customer Service700 A.M. 500 P.M. U.S. Pacific Time Before you contact Support… End Notes FCC WantsYou to Know This booklet is available from Glossary Panel See Frame Glossary This page intentionally left blank Arrow keys ix, 23, 24, 25, 37, 42, 44 Clean ix, 24, 33, 41, 46Calibration 27, 42-46, 49 Design software 15, 17, 19, 24, 28, 36, 51, 52, 54, 57, 61 Baud rate 18, 19, 25, 27, 28, 44, 52DM/PL 15, 19, 20 EPS 27 PLT 27 PLX 27 Feed shaft x, 30, 31, 35, 42, 55, 63File formats 15, 19, 20 Index Media 15, 16, 51 Stalls xii, 29Set origin 24, 36, 37, 42, 44, 54, 56 Origin 16, 21, 24, 36, 37, 42, 44, 53, 54, 56 Platen xi, xii, xiii, 33, 41, 55, 56 Power cord xiv, 18, 21, 41Power switch xi, xiv, 21 Frame 16, 28, 54 Sensor xii, 25 Service Station ix, xii, 21, 24, 33, 36, 46, 48, 50, 53Stop mode 23, 24, 25, 29, 37, 50 Serial port xi, xiv, 15, 17, 18, 19, 25, 52 Unroll v, 23, 25, 32, 37, 39, 50 Traverse xii, 41USB xi Index