Keypad Controls, Start/Stop | HP StudioJet, FlexJet E instruction

Keypad Controls

The keypad provides access to the main functions of the printer.

Figure 13. The Printer Keypad.

Start/Stop

The Start/Stop key toggles the printer online and offline. If the Start/

Stop key is pressed during printing, the OK light turns red and the machine will stop after it finishes printing the current scan. The Arrow, Unroll and Paper Advance keys are active when in STOP mode. When the Start/Stop key is pressed again, the printer enters START mode, the OK light turns green and printing resumes ex- actly where it stopped.

START mode	OK = green	Arrow keys inoperable,
		printer online (ready to re-
		ceive instructions).
STOP mode	OK = red	Arrow keys operable,
		printer offline (not ready to
		receive instructions).

CHAPTER 3

Operation

Image 21

HP StudioJet, FlexJet E manual Keypad Controls, Start/Stop

Contents

User Guide User Notice Ioline Flexjet E Printers Table of Contents Routine Maintenance Glossary Index Page Page Safety & Cautions Visual Reference Guide KM N AB C D E F Getting Started Chapter Ioline FlexJet E User Guide How The Ioline FlexJet E and StudioJet printers Work Unpacking the Printer Printer AssemblyAssembling the Stand Attaching the Printer to the Stand Serial Configuration Cable ConnectionsCOM Port Software Setup Options Other Serial Port SettingsInstallation Baud Rate CAD Installing FlexPlot and the Control Center Power On This page intentionally left blank Start/Stop Keypad Controls Clean QualitySet Origin Special Key Combinations Variety of settings are adjustable to fit specific needs Changing System SettingsControl Center Overview File Control Center Menu Bar FeaturesCommunications Tools Control Center Menu Options Consumables Printing a Marker General GuidelinesSend marker/plot files Loading Paper on the FlexJet E Loading Paper on the StudioJet FlexJet E only Installing the Take-up Shaft 2H+ FlexJet E Feeding Paper Positioning the Pinchwheels Tape Paper to theTake-up Shaft Positioning the pinchwheels Insert Front Dancer Bar Insert Rear Dancer Bar2H+ FJE Models Only Pausing a Marker PlotSet an Origin Sending Plot Files Removing Markers from the Take-up Shaft Canceling a Marker Plot Manually freeing the take-up shaft Manually Freeing Take-up Shaft Reattach Paper To the Take-up Shaft Automatically Freeing the Take-Up Shaft Printing to the Floor Cleaning the Platen and Traverse Cleaning the Drive Shaft Cleaning the Support Blocks Size CalibrationPrepare the Printer See the Operation chapter Click on Done when finished Routine Maintenance Use the Control Center to Gather the Calibration DataEnter the Calibration Data Prepare the Printer Cartridge Calibration Motion Adjust Carriage Scan Alignment Click on Done when finishedFrame Gap Paper Scan Alignment Cartridge Maintenance and Handling Automatic Cleaning ProcedureCheck Cartridges Manual Cleaning Procedure Soft, fiberless, and moistened with deionized waterOpen the latch for the first cartridge and remove it Print Cartridge Storage Update the Firmware Reset Calibration Values Media Tracking General Troubleshooting Printing Quality Line QualitySerial Communication Troubleshooting Keypad Error Codes Printer does not complete the marker Cause Common Issues Quick Start Guide to level Regular or intermittent paper tearing Cause FlexJet E Models only This page intentionally left blank Getting Help Service & Support Customer Service Your Comments Are Requested700 A.M. 500 P.M. U.S. Pacific Time End Notes Before you contact Support… This booklet is available from FCC WantsYou to Know Glossary Panel See Frame Glossary This page intentionally left blank Clean ix, 24, 33, 41, 46 Arrow keys ix, 23, 24, 25, 37, 42, 44Calibration 27, 42-46, 49 Baud rate 18, 19, 25, 27, 28, 44, 52 Design software 15, 17, 19, 24, 28, 36, 51, 52, 54, 57, 61DM/PL 15, 19, 20 File formats 15, 19, 20 Feed shaft x, 30, 31, 35, 42, 55, 63EPS 27 PLT 27 PLX 27 Index Set origin 24, 36, 37, 42, 44, 54, 56 Stalls xii, 29Media 15, 16, 51 Origin 16, 21, 24, 36, 37, 42, 44, 53, 54, 56 Power switch xi, xiv, 21 Power cord xiv, 18, 21, 41Platen xi, xii, xiii, 33, 41, 55, 56 Frame 16, 28, 54 Stop mode 23, 24, 25, 29, 37, 50 Service Station ix, xii, 21, 24, 33, 36, 46, 48, 50, 53Sensor xii, 25 Serial port xi, xiv, 15, 17, 18, 19, 25, 52 Traverse xii, 41 Unroll v, 23, 25, 32, 37, 39, 50USB xi Index