Required connections, Rtty Terminal | Icom iC-706MKTMG guide

2 INSTALLATION AND CONNECTIONS

■Required connections

AF RF/SQL HF/VHF/UHF TRANSCEIVER i706MK™G

MODE

BAND

POWER	TS

P.AMP/ATT

TUNER/CALL RIT/ SUB

M-CH SHIFT

PHONES

DISPLAY

LOCK

BAND

MENU	F-1	F-2	F-3	Z
				Z

HF/50 MHz ANTENNA			2 m ANTENNA

MICROPHONE (p. 8)

ANT 1

	RTTY TERMINAL	HM-103
	UNIT (p. 35)	HM-103
	UNIT (p. 35)

MIC

CW KEY (p. 33)

KEY

TUNER	EXT SP	DC 13 . 8V
	EXT SP

GND

ANT 2

GROUND (p. 9)

Use the heaviest gauge wire or strap available and make the connection as short as possible.

Grounding prevents electrical shocks, TVI and other problems.

PS-85

See p. 13 for details.

Page 14

Image 14

Icom iC-706MKTMG, HF/VHF/UHF ALL MODE TRANSCEIVER manual Required connections, Rtty Terminal

Contents

I706MKG Precautions Word Definition Rwarning Table of Contents 0MAIN Dial Tension Latch Panel DescriptionFront panel 2LOCK Switch Lock @2PREAMP/ATTENUATOR Switch P.AMP/ATT Function switches BREAK-IN p VOX Function pSpeech Compressor p Function p Rear and side panels ACC Socket When connecting the ACC conversion cable OPC-599ACC PIN # Name Description Specifications Color 4DSP Indicators 1DOT Matrix Indicators3FUNCTION Indicators Function display Microphone Connector ➊UP/DOWN Switches UP/DN ➋LOCK Switch Lock➌PTT Switch PTT HM-103 Schematic Diagram Unpacking Installation and ConnectionsPL-259 Connector Installation Example Grounding Stand InstallationSingle body mounting Front panel separation Required connections Rtty Terminal Advanced connections Connecting a NON-ICOM DC Power Supply Power supply connectionsConnecting the PS-85 DC Power Supply Connecting a NON-ICOM Connecting the IC-PW1 Connecting the AH-4Connecting the AT-180 External antenna tuners and linear ampliﬁer Initial settings Frequency SettingWhen ﬁrst applying power CPU resetting Power OFF VFO description VFO ModeMemory Mode pgs VFO Hz and 10 Hz tuning steps Frequency settingProgrammable tuning steps Band selection SSB/CW/RTTY modes Any mode FM/WFM/AM modes MHz quick tuning stepTS Switch Flow Chart Sub dial function Quick band change function Mode selectionOperating Mode Selection ➁ Push F-1-F-3 to select a band stacking register If shift function Receive and TransmitFunctions for receive RIT function Preamp and attenuator Noise blankerAGC time constant Peak meter hold RF/SQL control priority RF gain and squelchSimple band scope Filter ON/OFF Filter PresettingOptional ﬁlter selection SSB NR Noise Reduction function Ceiver maintains the ON/OFF condition when pushing F-2NRANF Automatic Notch Filter function DMeter function Output power and mic gainFunctions for transmit Speech compressor VOX operation Tuner Operation Manual TuningOptional AT-180 Automatic Antenna Tuner operation AH-4 operation ➂ The Tuner light lights constantly when tuning is completeOptional AH-4AUTOMATIC Antenna Tuner operation PTT tune function ➀ Select VFO a and set the frequency to 7.057 MHz/CW Split frequency operationQuick split function Split lock function Repeater operation ➄ Push and hold PTT to transmit release PTT to receive ➅ Communicate in the usual manner Tone squelch operationTone scan operation ➂ Push F-3SCN to toggle tone scan operation on and OFF This function automatically activates the repeater set One-touch repeater functionAuto repeater function Frequency Duplex Direction CW operation Functions for CWConnections for CW Elec KEY Setting the electronic keyer CW reverse modeDElectronic CW keyer Quick SET Mode CW pitch control Connections for Afsk Functions for RttyConnections for Rtty FSK Rtty Afsk operation Presetting for RttyRtty FSK operation Connections for packet Adjusting the transmit signal output from the TNCPacket operation Data socket Plot measurement Measuring SWRSpot measurement Memory channel selection Memory and Scan OperationMemory channels Memory clearing Memory/call programming Programming in VFO modeProgramming in memory mode Calling up memory names Frequency transferringMemory names Editing programming memory names Calling up a frequency from a memo pad Memo padsWriting frequencies and operating modes into memo pads ➀ Select the S1 display Scan types Preparation Select memory scan operation Programmed scan operationMemory scan operation Priority watch Data format Remote Jack CI-V InformationCI-V connection example Command Table VFO A=B Initial set mode operation SET ModeQuick set mode operation General Q2 MIC Gain SSB/AM/FM only Quick set mode itemsQ3 VOX Delay SSB/AM/FM only Q4 VOX Gain SSB/AM/FM only Q5 Anti VOX SSB/AM/FM only Initial set mode items RF/SQL SQL/AUTO/RFSQL SPL Offset split offset Quick Split quick split functionSplit Lock split lock DUP HF duplex offset Auto Rptr auto repeater AM NB Noise blanker in AM modePWR on CHK Power on check Scan Resume scan resume PTT Tune PTT tune function 29 9600 Mode Data socket speedTune Strt auto tuner start Vsend SEL ACC socket output CI-V Baud CI-V data rate LVL Spch S-level speechCI-V Addres CI-V address CI-V TRN CI-V transceive Memory backup MaintenanceFuse replacement Cleaning Troubleshooting Power Supply Receive Problem Possible Cause Solution Transmit Display Scan Problem Possible Cause Solution Optional INSTALLATIONS/SETTINGS Opening the transceiver case If ﬁlters Installation DOperation PIN no Description Name AT-180 internal switch descriptionS2 S1 B a Bottom view Internal ViewsTop view Options SP-20EXTERNAL Speaker SP-7EXTERNAL SpeakerSP-10EXTERNAL Speaker SP-12EXTERNAL Speaker SP-21EXTERNAL Speaker Specifications Menu Guide + power onPower OFF then on to exit initial set mode Indication Description No. Indication For 2 sec SSB/AM/FM mode CW mode Rtty modeMode Display Menu Display Count on us

■Required connections

RTTY TERMINAL

GROUND (p. 9)