Integra DTR-9.1 appendix Rear panel facilities, Antenna, Amp In, Pre Out, Monitor Out, Ac Outlets

Rear panel facilities

ANTENNA

These jacks are for connecting the FM indoor antenna and AM loop antenna that are supplied with the DTR- 9.1.

AMP IN

These jacks are for connecting a graphic equalizer for further control of the audio output.

•When connecting a graphic equalizer, remove the attached jumper plugs and store them carefully so as not to lose them.

•Only remove the jumper plugs when required. After you finish using an AMP IN jack, replace the jumper plug.

PRE OUT

These jacks are for connecting auxiliary power amplifi- ers.

•When connecting auxiliary power amplifiers, re- move the attached jumper plugs and store them carefully so as not to lose them.

•Only remove the jumper plugs when required. After you finish using a PRE OUT jack, replace the jumper plug.

MONITOR OUT

There are 2 monitor outputs and each one includes both composite video and S-video configurations. When connecting two video monitors or televisions, be aware that the OSD interface can only be used with MONITOR OUT 1 (OSD will not be displayed on the video monitor connected to MONITOR OUT 2).

DIGITAL INPUT/OUTPUT

(coaxial, optical, and input-only AC-3RF)

•When using the digital inputs and outputs, make sure to also connect the analog connections when- ever possible.

•When using one of the optical input or output jacks, remove the protective cap and keep it safely. When the jack is not used, replace the protective cap.

•When using an optical input or output jack, always use an optical fiber cable.

COMPONENT VIDEO INPUT/OUTPUT

If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the DTR-9.1. The DTR-

9.1has three component video input connectors to obtain the color information (Y, PB, PR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device. By sending the pure DVD component video signal di- rectly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly lifelike colors and crisp detail.

Y PB PR RCA type

AC OUTLETS

The DTR-9.1 is supplied with two AC mains outlets for connecting the power cords from other devices so that their power is supplied through the DTR-9.1. By doing this, you can use the STANDBY/ON button on the DTR- 9.1 to turn on and off the connected devices as well.

These are the digital audio inputs and outputs. There are 5 digital inputs with coaxial jacks, 3 with optical jacks, and 1 AC-3RF input. The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component. For digital output, there is 1 coaxial output and 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, DAT decks, or other similar components.

COAXIAL Coaxial cable

								AC 120V 60Hz
								SWITCHED
								AC OUTLETS TOTAL 120W 1A MAX.
	INPUT 2			INPUT 3			OUTPUT
Y	P	P	Y	P	P	Y	P	P

AV RECEIVER

MODEL NO. DTR-9.1

	L
	FRONT	AC
	SPEAKERS	INLET
	( 6 OHMS MIN.)
	R
	CENTER
	SPEAKER
	( 6 OHMS MIN.)
12V TRIGGER		IR IN
	MAIN	ZONE 2
A	B

AC OUTLETS

AC 120V 60Hz

SWITCHED

TOTAL 120W 1A MAX.

AC-3RF	Coaxial cable
OPTICAL	Optical fiber cable

Optical digital input terminal

An optical digital input terminal is equipped with a protection cap. When connecting, remove this cap. When not using, put the cap back on the terminal.

Caution

Make sure that the total capacity of the other compo- nents connected to this unit does not exceed the ca- pacity that is printed on the rear panel. For this model, the capacity is 120 watts.

13