Integra DTR-9.1 appendix Programming procedure, Buttons

Programming the commands of remote controllers for other devices into the remote controller

The remote controller has two learning functions. One is a normal learning function that enables the remote controller to learn the codes from other remote controllers. The other is a macro learning function that enables you to program of series of operations into the remote controller so that they can all be performed at once by pressing one button.

S5

E

M

LU

OV

G

IN

TU

M

TEN

S

O

ET T

L

ES

CH

T

D

SEE

E

C

R

P

D

P

HC TU

E

VD

A

ON

N

-I P

TU

LTUIN

O

P

M

RPH

UO

E

O

R

R D

T R

G

O

EC

E

2-

D

ISC

SU

M

LEN

C

ER

S TU

OE

D

T

ID

M

PU E

V

IM

IN P

1

D

AT

-O

P

E

E

D

IDV

EL

S

VD

RE

W

OP

5 to 15 cm

(2 to 6 inches)

SEND/LEARN

indicator

MODE

buttons

AUDIO

MUTING

TRACK

DISC

REC

OPEN/COLSE

DVD

CD

T1

T2

TUN

PH

V1

V2

V3

V–

STEREO

DIRECT

DSP

1

2

3

SURROUND

THX

DSP

4

5

6

Re-EQ

CH SEL

LEVEL +

7

8

9

LATE NIGHT DIMMER

LEVEL –

ENT

+ 10

0

ENT

HOME THEATER CONTROLLER

RC-418M

Programming procedure

When programming the commands of another remote controller to the RC-418M remote controller, you must first decide under which MODE button you want the commands to be linked. In general, you will select the MODE button that corresponds to the component you are programming. For example, if you are programming the functions from a remote controller for a compact disc player, you would choose the CD MODE button. Then, by pressing the CD MODE button, the buttons on the RC-418M remote controller will change to the commands you program here to operate the compact disc player.

After programming which MODE button to use, you will then transfer the separate commands from the other remote controller over to the RC-418M remote control- ler one at a time. Each command is then programmed to a different button on the RC-418M remote controller. Any button is programmable for this step except for the eight MODE buttons (AUDIO, CD, DVD, MD, SAT, CABLE, VCR, and TV), the two MACRO buttons (DIRECT and MODE), and the LIGHT button.

Even after the commands have been memorized, keep your old remote controller in a safe place. If for some reason the commands are lost (e.g., when the batteries run down), it will be necessary to memorize them once again.

1.Place the remote controller and the remote controller for the other device facing each other at a distance of 5 to 15 cm (2 to 6 inches) apart.

2.While pressing and holding down the desired MODE button on the remote controller, press the ENT button and then release both buttons.

When you press and hold down the MODE button, the SEND/LEARN indicator lights. When you press the ENT button, the lamp turns off. When you release the buttons, the lamp lights again and “LEARN” ap- pears in the display.

3.Press and release the button on the remote controller to which you want to transfer the next command.

You may select any button but the eleven ones indi- cated in the figure below. When you press the but- ton, “RCV” appears in the display and the SEND/ LEARN indicator turns off. When you release the but- ton, the indicator lights again.

If you press the wrong button by mistake, press that same button again. The SEND/LEARN indicator flashes twice, “CLEAR” appears in the display, and the remote controller exits the programming mode.

	LIGHT
DIRECT	MODE
MACRO	MACRO
	MODE
	buttons

: Buttons that cannot be programmed. 61