Integra DTR-9.1 appendix Other upgraded function, Input Setup, Delay sub-menu, Audio, button

Input Setup Other upgraded function

2-5. Delay sub-menu

This sub-menu gives you various ways to adjust the timing of the audio output from the speakers to give certain soundfield effects or to adjust for unwanted asynchronous video and audio tracks.

This sub-menu does not appear if “Direct” is selected as the listening mode.

Menu

123456789012345678901234 1.Speaker Setup

12.Input Setup

2.Input Setup

2 Input:TAPE1

3.Listening Mode Setup

3 123456789012345678901234 4.Preference

4121-.5Digit.Delayl Setup

5.Zone2 OSD Setup

522.MulInput:TAPE1tichannel Setup

6.About

633a..VideoA/VSyncSetup : 0.0ms

744.Listening Mode Preset

855Relative.SoundEffDelayct

Select: Exit:EXIT

966b..CharacterCenter Input:0.0ms Enter:ENTER Quit:OSD

077c..MiscellaneousSurrL/R :Setup0.0ms

18 d.Surr Back : 0.0ms

29Quit:OSD

2Quit:OSD

a. A/V Sync

If the video signal is progressive-processed using projector or other devices, the sound and picture may not match and the sound is heard too early. In such a case, use this setting to properly synchronize the audio and video. This setting can be set between 0 and 120 ms in 0.5-ms increments. Under normal circumstances, this can left at 0 ms. For input sources using the multi channel port, this setting will not appear.

Note:

When you use the listening mode of DTS 96/24, A/V Sync and Relative Delay will not be activated.

Selecting audio input signal using the AUDIO button on the remote controller (new function)

AUDIO	AUDIO	MUTING
	TRACK	DISC
button

Press the AUDIO button on the remote controller to change the audio mode. Each time the button is pressed, the mode changes from “AUTO” → “Multichannel” → “Analog” and back to “AUTO.” The “AUTO” audio mode is recommended for normal circumstances.

AUTO (automatic detection): With this setting, this unit automatically detects whether the input signal is digital or analog. When a digital signal is not input, then the analog signal is played. This setting is effective when the input source is assigned to Digital Input in Audio Setup.

Multichannel: Select this setting to play back the input from the component connected to the MULTI CHANNEL INPUT port. This setting is effective when the Multichannel setting in “2-2. Multichannel Setup” is set to “Yes.”

Analog: Select this setting to play back the input from a source component connected to an analog audio input jacks. With this setting, even if a digital signal is input from the same component, only the analog signal will be output.

ONKYO CORPORATION

Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8111 Fax: 072-833-5222

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 201-785-2600 Fax: 201-785-2650 E-mail: onkyo@onkyousa.com

ONKYO EUROPE ELECTRONICS GmbH

Industriestrasse 20, 82110 Germering, GERMANY

Tel: 089-849-320 Fax: 089-849-3265 E-mail: info@onkyo.de

ONKYO CHINA LIMITED

Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,

N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039

	Printed in Japan
SN 29343353	D0203-1

E