Integra DTR-9.1 appendix Front panel facilities

Front panel facilities

Front panel

Power

After plugging in the power cord into the rear panel and wall outlet, pressing this button connects the DTR-9.1 to the AC mains and turns it on.

•Before turning on the power, make sure all cables are properly connected.

•Turning on the DTR-9.1 may cause a momentary power surge that might interfere with other electrical equip- ment on the same circuit. If this is a problem, plug the DTR-9.1 into a different electrical circuit.

Standby/On

Pressing this button while the main power is turned on the STANDBY indicator lights up and the front display turns off. Pressing it again returns it to the standby state. This state turns off the display, disables control functions, and turns off all outputs to the main zone (those for the remote zone remain available).

Standby indicator

Master Volume

The MASTER VOLUME knob is used to control the volume for the main zone. The volume for the remote zone (Zone 2) is independent.

Open/Close

Press this button to open and close the front door that covers the lower buttons.

Display

The DISPLAY button is used to display information about the current input source signal. Each time you press the display button, the screen changes to show you different information concerning the input signal.

The screen changes as follows:

Program format → Sampling frequency → Digital input → Digital format → Bass level → Treble level.

If the input source signal does not have any information for a particular screen, then that screen will be skipped.

•Displaying the data of the current input source Each display is explained below.

LFE(Low Frequency Effect)

Program format:

Front channel Surround channel

Source signal 48 kHz

Sampling frequency:

Sampling frequency

Digital input:

The current input source is set for digital input at OPT1.

Digital format:

The current input source is set for a digital format of “Auto.”

Bass level:

The current bass level is +2.

Treble level:

The current treble level is -2.

Input Source Buttons (DVD, VIDEO 1–5, TAPE 1–2, AM, FM, PHONO, and CD) and Indicator

These buttons are used to select the input source for the main zone. When an input source is selected, the indica- tor will light in orange. To select the input source for the remote zone (Zone 2) or recording out (Rec Out), first press the Zone 2 or Rec Out button, and then the desired input source button.

Zone 2/Rec Indicator

For Zone 2, the indicator above the selected input source button will light green. For recording, it will light red.

Front panel door

Caution:

The front door of the receiver is motorized. Use the open/ close button to open or close the door. Manually opening or closing the door, or moving the receiver while holding the door, will cause the door to malfunction or break.

Rec Out

Press the Rec Out button to output to a recording compo- nent for recording purposes. After pressing the Rec Out button, press one of the input source selector buttons within 8 seconds to select the component to record to. When one is selected, the indicator above that button will light in red. To record from the same input source that you are using (that is selected for the main zone), press the Rec Out button twice in succession.

Note:

The Rec Out and Zone 2 buttons use the same circuit and therefore cannot be used at the same time.

When Rec Out is selected, nothing is output from Zone 2.

Zone 2

The DTR-9.1 includes a second signal path separate from the main one that can be used for a remote zone (Zone 2) or for making recordings. By connecting an additional amplifier or other video equipment to the Zone 2 outputs, you can output to a separate room an input source that is different from that being used in the main room. This al- lows you to watch one program in one room while some- body else is watching a different program in another.

Press the Zone 2 button to enable output to the ZONE 2 outputs. After pressing the Zone 2 button, press one of the input source selector buttons within 8 seconds to select the input source for the remote zone. When one is se- lected, the indicator above that button will light in green.

9