Manuals / Brands / Computer Equipment / Computer Hardware / Intel / Computer Equipment / Computer Hardware

Intel S5000PSL, S5000XSL 3.3.1Video Modes, 3.3.2Video Memory Interface, 3.3.3Dual Video

1 120

Download 120 pages, 3.3 Mb

Intel® Server Boards S5000PSL and S5000XSL TPS

Design and Environmental Specifications

3.3.1Video Modes

The ATI* ES1000 chip supports all standard IBM* VGA modes. The following table shows the 2D modes supported for both CRT and LCD.

Table 7. Video Modes

2D Mode	Refresh Rate (Hz)		2D Video Mode Support
		8 bpp		16 bpp	32 bpp
640x480	60, 72, 75, 85, 90,	Supported		Supported	Supported
	100, 120, 160, 200

800x600	60, 70, 72, 75, 85,	Supported		Supported	Supported
	90, 100, 120,160

1024x768	60, 70, 72,	Supported		Supported	Supported
	75,85,90,100

1152x864	43,47,60,70,75,80,85	Supported		Supported	Supported

1280x1024	60,70,74,75	Supported		Supported	Supported
1600x1200	52	Supported		Supported	Supported

3.3.2Video Memory Interface

The memory controller sub-system of the ES1000 arbitrates requests from the direct memory interface, the VGA graphics controller, the drawing co-processor, the display controller, the video scalar, and the hardware cursor. Requests are serviced in a manner that ensures display integrity and maximum CPU/co-processor drawing performance.

The server board supports a 16 MB (4 Meg x 16-bit x 4 banks) DDR SDRAM device for video memory.

3.3.3Dual Video

The BIOS supports single- and dual-video modes. The dual-video mode is enabled by default.

In single mode (Dual Monitor Video = disabled), the on-board video controller is disabled when an add-in video card is detected.

In dual mode (On-board Video = enabled, Dual Monitor Video = enabled), the on-board video controller is enabled and will be the primary video device. The external video card will be allocated resources and is considered the secondary video device. The BIOS Setup utility provides options to configure the feature as follows.

On-board Video	Enabled
	Disabled

Dual Monitor Video	Enabled	Shaded if on-board video is set to "Disabled"
	Disabled

Revision 1.2	47
	Intel order number: D41763-003

Contents

Revision September Enterprise Platforms and Services Division – Marketing Revision History Disclaimers Table of ContentsIntel® Server Boards S5000PSL and S5000XSL TPS Table of Contents Intel® Server Boards S5000PSL and S5000XSL TPS Table of Contents Page Appendix C: POST Code Diagnostic LED Decoder List of Figures List of Tables List of Tables Page This page intentionally left blank 1.Introduction 1.1Chapter Outline 1.2Server Board Use Disclaimer Page 2.Server Board Overview 2.1Server Board Feature Set Page Page 2.2Server Board Layout 2.2.1Server Board Connector and Component Layout Figure 2. Major Board Components 2.2.2Server Board Mechanical Drawings Page Figure 5. Restricted Areas on Side Figure 6. Restricted Areas on Side Page Figure 8. CPU and Memory Duct Keepout 2.2.3Server Board ATX I/O Layout 3.Functional Architecture Page 3.1Intel® 5000P / 5000X Memory Controller Hub (MCH) 3.1.1System Bus Interface 3.1.2Processor Support 3.1.2.1Processor Population Rules 3.1.2.2Common Enabling Kit (CEK) Design Support Page 3.1.3Memory Sub-system 3.1.3.1Memory RASUM Features 3.1.3.2Supported Memory Note 3.1.3.3DIMM Population Rules and Supported DIMM Configurations Page Page 3.1.3.3.1Minimum Non-MirroredMode Configuration Grey 3.1.3.4Non-mirroredMode Memory Upgrades 3.1.3.4.1Mirrored Mode Memory Configuration 3.1.3.4.2Sparing Mode Memory Configuration Intel® 5000P/5000X Memory Controller Hub 3.1.4Snoop Filter (5000X MCH only) 3.2Enterprise South Bridge (ESB2-E) 3.2.1PCI Sub-system 3.2.1.1PCI32: 32-bit, 33-MHzPCI Sub-system 3.2.1.2PXA: 64-bit, 133-MHzPCI Sub-system 3.2.1.3PE0: One x4 PCI Express* Bus Segment 3.2.1.4PE1: One x4 PCI Express* Bus Segment 3.2.1.5PE2: One x4 PCI Express* Bus Segment 3.2.2Serial ATA Support 3.2.3Parallel ATA (PATA) Support 3.2.4USB 2.0 Support 3.3Video Support Page 3.3.1Video Modes 3.3.2Video Memory Interface 3.3.3Dual Video 3.4SAS Controller 3.4.1SAS RAID Support 3.4.2SAS / SATA Connector Sharing 3.5Network Interface Controller (NIC) 3.5.1Intel® I/O Acceleration Technolgy 3.6 Super I/O 3.6.1Serial Ports 3.6.2Floppy Disk Controller 3.6.3Keyboard and Mouse Support 3.6.4Wake-upControl 3.6.5System Health Support 4.Platform Management Page 5.Connector / Header Locations and Pin-outs 5.1Board Connector Information 5.2Power Connectors Table 12. 12 V Power Connector Pin-out(J3J2) Table 13. Power Supply Signal Connector Pin-out(J9D1) Table 14. P12V4 Power Connector Pin-out(J5A2) 5.3System Management Headers 5.3.1Intel® Remote Management Module (Intel® RMM) Connector 5.3.2LCP / AUX IPMB Header 5.3.3IPMB Header 5.3.4HSBP Header 5.3.5SGPIO Header 5.3.7HDD Activity LED Header 5.4Front Panel Connector 5.5I/O Connectors 5.5.1VGA Connector 5.5.2NIC Connectors 5.5.3IDE Connector 5.5.4Intel® Remote Management Module NIC Connector Page 5.5.5SATA / SAS Connectors 5.5.6Serial Port Connectors 5.5.7Keyboard and Mouse Connector 5.5.8USB Connector 5.6Fan Headers Page 6.Jumper Blocks 6.1CMOS Clear and Password Reset Usage Procedure 6.2BMC Force Update Procedure 6.3BIOS Select Jumper 7.Intel® Light Guided Diagnostics 7.15 Volt Standby LED 7.2Fan Fault LEDs 7.3System ID LED and System Status LED 7.3.1System Status LED – BMC Initialization Page 7.4DIMM Fault LEDs 7.5Processor Fault LEDs 7.6Post Code Diagnostic LEDs 8.Design and Environmental Specifications 8.1Server Boards S5000PSL and S5000XSL Design Specifications 8.2Server Board Power Requirements 8.2.1Processor Power Support 8.3.1Grounding 8.3.2Standby Outputs 8.3.3Remote Sense 8.3.4Voltage Regulation 8.3.5Dynamic Loading 8.3.6Capacitive Loading 8.3.7Ripple / Noise 8.3.8Timing Requirements Table 44. Output Voltage Timing Figure 25. Output Voltage Timing Table 45. Turn On/Off Timing Figure 26. Turn On/Off Timing (Power Supply Signals) 8.3.9Residual Voltage Immunity in Standby Mode 9.Regulatory and Certification Information 9.1 Product Regulatory Compliance 9.1.1Product Safety Compliance 9.1.2Product EMC Compliance – Class A Compliance 9.1.3Certifications / Registrations / Declarations 9.2Product Regulatory Compliance Markings 9.3 Electromagnetic Compatibility Notices 9.3.1FCC Verification Statement (USA) 9.3.2ICES-003(Canada) 9.3.3Europe (CE Declaration of Conformity) 9.3.4VCCI (Japan) 9.3.5BSMI (Taiwan) 9.3.6RRL (Korea) 9.3.7CNCA (CCC-China) 9.4Restriction of Hazardous Substances (RoHS) Compliance Appendix A: Integration and Usage Tips Appendix B: BMC Sensor Tables ƒRearm Sensors ƒDefault Hysteresis ƒCriticality ƒStandby Table 46. BMC Sensors Page Page Page Page Page Page Page Page Page Page Page Page Appendix C: POST Code Diagnostic LED Decoder Table 47. POST Progress Code LED Example Table 48. Diagnostic LED POST Code Decoder Page Page Page Appendix D: POST Code Errors Page POST Error Beep Codes Appendix E: Supported Intel® Server Chassis Glossary Page Page Reference Documents