Euro Support, Printer Firmware Requirements | Intermate LX T-04

A p p e n d i c e s

E. Euro Support

Support for the Euro symbol can be achieved in two ways. Either by updating the LX T-04 firmware and selecting the Euro character set or by making a permanent character substitution in the interface. Both approaches require that the printer firmware supports the Euro symbol and are covered by this appendix.

The interface firmware release K12-8491and above supports the Euro symbol via the new ASCII character set "PC-858". This is achieved by replacing the

international currency “¤” symbol with that of the Euro symbol “ €”. The character set is selected via the terminal configuration method.

Permanent substitution of the international currency symbol with the Euro symbol is done by sending a command sequence to the interface. This approach does not require the interface firmware to be updated, as only the character number is sent to the printer.

Printer Firmware Requirements

In order to be able to print the Euro symbol, the printer firmware has to meet the minimum firmware requirement listed in the below table.

Printer model	Required firmware

Lexmark 23xx	version 1.7 (or greater)
Lexmark 4227	Version 3.1 (or greater)
Lexmark 4227 Plus	There is no minimum firmware
	requirement for this printer.

Refer to your printer’s User’s Guide for instructions on how to check and upgrade the firmware.

I n t e r m a t e L X T - 0 4

65

Image 65

Intermate LX T-04 manual Euro Support, Printer Firmware Requirements

Contents

LX T-04 Emission Notices Trademark Credits T i c e s E r ‘ s G u i d e Contents Solving Problems Index N t e n t s E r ‘ s G u i d e Configuration InstallationSolving Problems Introduction O u t t h i s m a n u a l E r ‘ s G u i d e Ascii Printer Driver Theory of Operation IBM Printer Emulation Optional UnpackingPrinter Attachment Example Printout System Attachment Make a test printout Configuration from the System Configuration from a TerminalConfiguration from a Terminal Key Definitions Select Basic Configuration Basic Configuration Select Printer Driver You can switch to another Printer Driver if you prefer IBM Printer Emulation Select IBM Printer Emulation System Language Select System Language Select Save in the Main Menu Save the ConfigurationSelect Yes to save the current configuration permanently Select Exit in the Main Menu Exit the ConfigurationSelect Yes to exit the configuration Advanced Functions Extended Emulation Mode See Section Main Menu Document example Configuration from the System Transparency Configuration and Transparency Sequences Redefine the Sequences Define the Sequences Edit Translation Tables Character Translation Appendix a Programming the Strings Example User Defined Strings String Substitutions Using the Strings Programming String Substitutions from a Terminal Edit Parameters Programming String Substitutions from the System Define Bar Codes Bar Codes Print Bar Code EAN13 Define Bar Code Missing Printouts Solving Problems Incorrect Host Printouts System printouts Is the System indicator on? Incorrect Page Breaks Host Communication ProblemCorrupted Printouts Printing the Parameter List Reporting Problems Producing Hexdumps Error messages Hardware error. Contact you dealer/distributor L v i n g P r o b l e m s E r ‘ s G u i d e Parameter List Appendices #10 System Language Printer Drivers #40 Escape Character #15 Ascii Character Set#26 IBM Printer Emulation #43 Transp./Config. Trailer Sequence #42 Configuration Lead-In Sequence#41 Transparency Lead-In Sequence #45 Job Time-out #53 Bar Code Driver #46 Start of Job Sequence#54 Bar Code Attributes #120-#129 User Definable Strings #150-#189 Ebcdic Character Table P e n d i c e s E r ‘ s G u i d e Start Conditions Operating the LX T-04 Device address Test Mode Select IBM Printer Emulation P e n d i c e s Checking if an update is available Softwarethat can be UpdatedUpdating the Software Updating the Intermate LX T-04 Flash ROM Copy K12-xxxx.bin lpt1 /b P e n d i c e s P e n d i c e s E r ‘ s G u i d e Printer Firmware Requirements Euro Support How to disable Euro support Euro Support via Terminal Configuration P e n d i c e s Edit Parameters Ascii Char. Set Euro Support via Command Sequences Attachments Technical SpecificationsSupported Printers IBM Printer Emulation IBM System FeaturesAdditionalIBM 4214 feature Hardware Specifications Intermate LX T-04 Additional FeaturesApprovals EMC Operating Environment P e n d i c e s E r ‘ s G u i d e Title Part Number Related Publications P e n d i c e s E r ‘ s G u i d e Customer Support P e n d i c e s E r ‘ s G u i d e Index D e D e