Footplate Depth Adjustment | Invacare TerminatorTM SS specs

FOOTREST / ANTI-TIPPER

SECTION 6	FOOTREST/ANTI-TIPPER

FOOTPLATE DEPTH ADJUSTMENT

1.Loosen, but do not remove the four (4) flat screws and locknuts that secure footplate to the footrest tubes.

NOTE: Observe the angle of footplate for reinstallation.

2.Move the footplate to one (1) of two (2) positions to accommodate the user.

3.Retighten the four (4) flat screws and locknuts.

NOTE: The settings for positioning the footplates on the half-clamps may vary for each end-user.

NOTE: The locknuts should lie in the channel of the footplate half clamp.

Allen Screws

	Footrest
	Tube
	ANGLE
	Flat
HEIGHT	Screws
HEIGHT
	Footplate

Flat Screws

DEPTH

FIGURE 3 - INSTALLING/ADJUSTING OPTIONAL A4 FOOTREST

Terminator™ SS

48

Part No. 1052712 Rev D

Image 48

Invacare TerminatorTM SS manual Footplate Depth Adjustment

Contents

Terminator SS Special Notes Special NotesWheelchair TIE-DOWN Restraints and Seat Positioning Straps Table of Contents Limited Warranty Specifications Specifications Stability Operating InformationGeneral Guidelines Section General Guidelines General Guidelines Section Do not tip the wheelchair without assistanceDo not operate on roads, streets or highways Weight Training Weight LimitationTire Pressure and Information SAFETY/HANDLING of Wheelchairs Stability and BalanceCoping with Everyday Obstacles Percentage of Weight Distribution Unoccupied OccupiedShortening Lengthening Tipping REACHING, Leaning Bending ForwardREACHING, Leaning Backwards Tipping Curbs Stairways Transferring to and from Other Seats ESCALATORS? Sorry Safety Inspection Checklist Safety InspectionSection Safety Inspection Troubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance Procedures Safety Inspection Back Section Back Section Back Back Angle to Seat Rail Adjusting Top End Back Upholstery TOP END Back Upholstery Figure Section Back Replacing Top End Back Upholstery Custom Manual Adjustable Tension Back Upholstery Figure Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Fastening Strap Hole Back Number Seat Section Seat Seat Section Replacing Custom Manual Screw on Seat Upholstery REMOVING/INSTALLING Rear Wheels Figure WheelsSection Wheels Adjusting QUICK-RELEASE Axles Figure Wheels Section Installing QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureAND/OR OUT Handrim Replacement Figure Removing Play from Rear Wheels REPAIRING/REPLACING Rear WHEEL, TIRE/TUBE OPENING/CLOSING Clamps FigureCamber Clamps Receiver Tube Clamps Camber Clamps Quick Release Lever Standard Closed PositionOpen Receiver Tube Clamps Adjusting Rear Wheel Camber Camber TubeA4 Camber System Figure Determining TOE IN/TOE OUT Figures 8 Determining TOE TOE OUT Measuring Centerlines of Rear Wheels Adjusting TOE IN/TOE OUT Course Adjustment FigureCamber Tube 2000 Figure A4 Camber System Adjusting TOE IN/TOE OUT A4 Camber System Course Adjustment Fine Adjustment Figure Adjusting TOE IN/TOE OUT A4 Camber System Fine Adjustment Adjusting Center of Gravity Never Operate Wheelchair with BothEnds of the Indexing Tape Showing Adjusting Wheelbase Width Wheelbase Width CamberTube Replacing Axle Tube Figure Front WheelchairRear Camber Adjusting the Axle Tube Axle Tube Camber Tube TOE IN/TOE OUT Measurement is Within ±1/8-INCH TOE IN/TOE OUT Measurement is not Within ±1/8-INCH REPLACING/ADJUSTING Casters Figure NON-SUSPENSION CasterSuspension Caster Adjusting Front Caster Height Figure Adjusting Front Caster Height Wheel Lock ADJUSTMENT/REPLACEMENT Figure Adjusting the High/Low Mount Wheel LockWheel Lock Adjustment Replacing the High/Low Mount Wheel Lock ADJUSTING/REPLACING Standard Footrest Figure If Replacing or Adjusting the FootrestIf Replacing the Footrest Footrest / ANTI-TIPPER INSTALLING/ADJUSTING Optional A4 Footrest Figure InstallingAdjusting Footplate Angle Adjustment Footplate Depth Adjustment Depth ANTI-TIPPER REPLACEMENT/ADJUSTMENT Figure ReplacementAdjustment Elastomers and Suspension Replacing Rear Elastomers FigureSuspension Section Suspension Suspension Section Replacing Rear Elastomers Replacing Front Elastomers Figure Detail C REMOVING/INSTALLING/REPLACING Suspension Tubes Figure Installing Suspension TubesRemoving Suspension Tubes Detail B Suspension Tube Hardware Adjusting SEAT-TO-FLOOR Height Figure Adjusting SEAT-TO Floor Height Repositioning the Axle Tube Figure Clamp Position Must be INVERTED- Proceed to Step Procedure Suspension Detail C Axle Tube Positions Suspension Procedure Repositioning Quick Release Levers FigureReverse Side View of Camber Clamp with Quick Release Lever Terminator SS Warranty Warranty Canada