OPENING/CLOSING Clamps Figure | Invacare TerminatorTM SS manual

WHEELS

SECTION 5	WHEELS

REPAIRING/REPLACING REAR WHEEL, TIRE/TUBE

WARNING

Replacement of the tire or tube MUST be performed by a qualified technician.

CAUTION

Changing the size of the rear wheels can affect the performance of the wheelchair. Contact Invacare at the numbers on the back cover BEFORE performing this procedure.

NOTE: If replacing rear wheels with a different size than what was originally on the wheelchair, the front caster height must also be changed to keep the wheelchair frame parallel to the floor. Refer to ADJUSTING CASTER HEIGHT in this section of the manual ONLY after contacting Invacare. Anti-tipper height (if applicable) must also be adjusted to maintain 1-1/2 to 2-inch clearance between bottom of the anti-tipper wheels and the floor. Refer to ANTI-TIPPER REPLACEMENT/ADJUSTMENT in SECTION 6 of this manual.

OPENING/CLOSING CLAMPS (FIGURE 6)

WARNING

QUICK RELEASE LEVERS - Make sure the quick release levers are in the CLOSED position BEFORE using the wheelchair, otherwise personal injury or damage to the wheelchair may result.

WARNING

STANDARD CAMBER OR RECEIVER TUBE CLAMPS - Make sure the hex screws and locknuts are securely tightened BEFORE using the wheelchair, otherwise personal injury or damage to the wheelchair may result.

CAUTION

DO NOT close the quick release levers or tighten the hex screws and locknuts without camber inserts in the axle tube. Damage to the axle tube will occur.

CAMBER CLAMPS

1.Perform one (1) of the following to open a camber clamp:

A.QUICK RELEASE LEVERS - Pull the quick release lever to the open position.

B.STANDARD CAMBER CLAMPS - Loosen, but do not remove the hex screw and locknut on the camber clamp.

2.Perform one (1) of the following to close a camber clamp:

A.QUICK RELEASE LEVERS - Tighten the threaded knob to secure the quick release lever. Push the quick release lever on the camber clamps to the closed position.

B.STANDARD CAMBER CLAMPS - Securely tighten the hex screw and locknut to secure the axle tube.

Terminator™ SS

30

Part No. 1052712 Rev D

Image 30

Invacare TerminatorTM SS manual REPAIRING/REPLACING Rear WHEEL, TIRE/TUBE, OPENING/CLOSING Clamps Figure, Camber Clamps

Contents

Terminator SS Special Notes Special NotesWheelchair TIE-DOWN Restraints and Seat Positioning Straps Table of Contents Limited Warranty Specifications Specifications General Guidelines StabilityOperating Information Section General Guidelines General Guidelines Section Do not tip the wheelchair without assistanceDo not operate on roads, streets or highways Weight Training Weight LimitationTire Pressure and Information SAFETY/HANDLING of Wheelchairs Stability and BalanceCoping with Everyday Obstacles Percentage of Weight Distribution Unoccupied OccupiedShortening Lengthening Tipping REACHING, Leaning Bending ForwardREACHING, Leaning Backwards Tipping Curbs Stairways Transferring to and from Other Seats ESCALATORS? Sorry Safety Inspection Checklist Safety InspectionSection Safety Inspection Maintenance Safety Precautions TroubleshootingMaintenance Suggested Maintenance Procedures Safety Inspection Back Section Back Section Back Back Angle to Seat Rail Adjusting Top End Back Upholstery TOP END Back Upholstery Figure Section Back Replacing Top End Back Upholstery Custom Manual Adjustable Tension Back Upholstery Figure Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Fastening Strap Hole Back Number Seat Section Seat Seat Section Replacing Custom Manual Screw on Seat Upholstery REMOVING/INSTALLING Rear Wheels Figure WheelsSection Wheels Adjusting QUICK-RELEASE Axles Figure Wheels Section Installing QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureAND/OR OUT Handrim Replacement Figure Removing Play from Rear Wheels REPAIRING/REPLACING Rear WHEEL, TIRE/TUBE OPENING/CLOSING Clamps FigureCamber Clamps Open Receiver Tube ClampsCamber Clamps Quick Release Lever Standard Closed Position Receiver Tube Clamps Adjusting Rear Wheel Camber Camber TubeA4 Camber System Figure Determining TOE IN/TOE OUT Figures 8 Determining TOE TOE OUT Measuring Centerlines of Rear Wheels Camber Tube 2000 Figure Adjusting TOE IN/TOE OUTCourse Adjustment Figure A4 Camber System Adjusting TOE IN/TOE OUT A4 Camber System Course Adjustment Fine Adjustment Figure Adjusting TOE IN/TOE OUT A4 Camber System Fine Adjustment Ends of the Indexing Adjusting Center of GravityNever Operate Wheelchair with Both Tape Showing Adjusting Wheelbase Width Wheelbase Width CamberTube Rear Replacing Axle Tube FigureFront Wheelchair Camber Adjusting the Axle Tube Axle Tube Camber Tube TOE IN/TOE OUT Measurement is Within ±1/8-INCH TOE IN/TOE OUT Measurement is not Within ±1/8-INCH REPLACING/ADJUSTING Casters Figure NON-SUSPENSION CasterSuspension Caster Adjusting Front Caster Height Figure Adjusting Front Caster Height Wheel Lock Adjustment Wheel Lock ADJUSTMENT/REPLACEMENT FigureAdjusting the High/Low Mount Wheel Lock Replacing the High/Low Mount Wheel Lock If Replacing the Footrest ADJUSTING/REPLACING Standard Footrest FigureIf Replacing or Adjusting the Footrest Footrest / ANTI-TIPPER Adjusting INSTALLING/ADJUSTING Optional A4 Footrest FigureInstalling Footplate Angle Adjustment Footplate Depth Adjustment Depth ANTI-TIPPER REPLACEMENT/ADJUSTMENT Figure ReplacementAdjustment Suspension Elastomers and SuspensionReplacing Rear Elastomers Figure Section Suspension Suspension Section Replacing Rear Elastomers Replacing Front Elastomers Figure Detail C Removing Suspension Tubes REMOVING/INSTALLING/REPLACING Suspension Tubes FigureInstalling Suspension Tubes Detail B Suspension Tube Hardware Adjusting SEAT-TO-FLOOR Height Figure Adjusting SEAT-TO Floor Height Repositioning the Axle Tube Figure Clamp Position Must be INVERTED- Proceed to Step Procedure Suspension Detail C Axle Tube Positions Reverse Suspension ProcedureRepositioning Quick Release Levers Figure Side View of Camber Clamp with Quick Release Lever Terminator SS Warranty Warranty Canada