Manuals / Brands / Personal Care / Mobility Aid / Invacare / Personal Care / Mobility Aid

Invacare Top End T-3 FRONT CASTER REPLACEMENT (FIGURE 17), ADJUSTING FRONT CASTER HEIGHT (FIGURE 18)

1 64

Download 64 pages, 617.32 Kb

Part No. 1054916 47 T-3™ and T-4™ Series

WHEELS

FRONT CASTER REPLACEMENT (FIGURE 17)

1. Remove the bolt and locknut that secure

the front caster to the mounting fork.

2. Remove the front caster and axle spacers

from the mounting fork.

3. Install the NEW front caster and spacers

onto the mounting fork and securely

tighten.

4. Repeat the procedure for the opposite

front caster if necessary.

NOTE: If replacing front casters with a different size

than what was originally on the chair, the front caster

height MUST be adjusted to keep the chair frame

parallel to the floor. Refer to ADJUSTING FRONT

CASTER HEIGHT in this procedure of the manual.

FIGURE 17 - FRONT CASTER

REPLACEMENT

ADJUSTING FRONT CASTER HEIGHT (FIGURE 18)

NOTE: When changing a rear wheel to a different

size, it becomes necessary to adjust the front caster

height so the chair frame will remain parallel to the

floor.

1. Place the wheelchair on a flat surface.

2. Remove the dust cover on the fork

assembly.

3. Remove the locknut that secures the

front caster fork to the chair frame.

4. Position a large right triangle or "L"

square on the flat surface and against the

caster housing that is welded to the chair

frame.

5. Adjust the height of the front casters by either adding or removing spacers on top of the

fork stem until the chair frame is parallel with the floor.

6. Reinstall the locknut and dust cover onto the chair.

NOTE: A 1/4-inch and 1/2-inch spacer are provided, however, it is possible that smaller washers may be

required to fine tune the caster height.

Mounting Fork

Bolt Locknut

Axle

Spacer

Front

Caster

Fork Stem

Spacers

Locknut Caster Housing

"L"

Square

FIGURE 18 - ADJUSTING FRONT

CASTER HEIGHT

PROCEDURE 6 WHEELS

WHEELS

Contents

Main SPECIAL NOTES NOTICE SPECIAL NOTES WARNING TABLE OF CONTENTS REGISTER YOUR PRODUCT! The benefits of registering: Register ONLINE at www.invacare.com - or - Complete and mail the form on the next page PRODUCT REGISTRATION FORM Page Page Page See current order form STABILITY STABILITY WARNINGS GENERAL GUIDELINES PROCEDURE 1 GENERAL GUIDELINES PROCEDURE 1 GENERAL WARNINGS (CONTINUTED) GENERAL WARNINGS (CONTINUTED) TIRE PRESSURE WEIGHT TRAINING WEIGHT LIMITATION SAFETY/HANDLING OF WHEELCHAIRS STABILITY AND BALANCE COPING WITH EVERYDAY OBSTACLES A NOTE TO WHEELCHAIR ASSISTANTS PERCENTAGE OF WEIGHT DISTRIBUTION PROCEDURE 1GENERAL GUIDELINES FUNCTIONAL REACH FROM A WHEELCHAIR TILTING STAIRWAYS GENERAL GUIDELINES PROCEDURE 1 TRANSFERRING TO AND FROM OTHER SEATS ESCALATORS? SORRY! SAFETY INSPECTION CHECKLIST SAFETY INSPECTION PROCEDURE 2 TROUBLESHOOTING SAFETY INSPECTIONPROCEDURE 2 SAFETY INSPECTION CHECKLIST (CONTINUED) MAINTENANCE SAFETY INSPECTION PROCEDURE 2 MAINTENANCE SAFETY PRECAUTIONS SUGGESTED MAINTENANCE PROCEDURES BACKPROCEDURE 3 ADJUSTING/REPLACING BACK UPHOLSTERY (FIGURE 1) ADJUSTING BACK UPHOLSTERY FIGURE 1 - ADJUSTING/REPLACING BACK UPHOLSTERY REPLACING BACK UPHOLSTERY PROCEDURE 3BACK FOLDING BACK (FIGURE 2) FIGURE 2 - FOLDING BACK BACK HEIGHT ADJUSTMENT (FIGURE 3) BACK PROCEDURE 3 FIGURE 3 - BACK HEIGHT ADJUSTMENT BACK ANGLE ADJUSTMENT (FIGURE 4) HOLE NUMBER FIGURE 4 - BACK ANGLE ADJUSTMENT 94 BACK ANGLE TO SEAT RAIL 90 BACK ANGLE TO SEAT RAIL 77 BACK ANGLE TO SEAT RAIL 73 BACK ANGLE TO SEAT RAIL SEAT UPHOLSTERY REPLACEMENT (FIGURE 1) FIGURE 1 - SEAT UPHOLSTERY REPLACEMENT REAR SEAT HEIGHT ADJUSTMENT FRONT SEAT HEIGHT ADJUSTMENT Before 2001 (FIGURE 4) After 2001 (FIGURE 5) PROCEDURE 4 SEAT FIGURE 4 - FRONT SEAT HEIGHT ADJUSTMENT - BEFORE 2001 RIGID CLOTHING GUARD REPLACEMENT (FIGURE 2) NYLON CLOTHING GUARD WITH PLASTIC INSERT REPLACEMENT (FIGURE 1) PROCEDURE 5CLOTHING GUARDS CLOTHING GUARDS FIGURE 1 - NYLON CLOTHING GUARD WITH PLASTIC INSERT REMOVING/INSTALLING REAR WHEELS (FIGURE 1) QUICK OR QUAD-RELEASE AXLES FIGURE 2 - ADJUSTING QUICK-RELEASE AXLES WHEELS PROCEDURE 6 ADJUSTING QUICK-RELEASE AXLES (FIGURE 2) FIGURE 1 - REMOVING/INSTALLING REAR WHEELS INSTALLING/ADJUSTING QUAD-RELEASE AXLES INSTALLING (FIGURE 3) FIGURE 3 - INSTALLING QUAD-RELEASE AXLES ADJUSTING (FIGURE 4) FIGURE 4 - ADJUSTING QUAD-RELEASE AXLES FIGURE 5 - HANDRIM HANDRIM REPLACEMENT (FIGURE 5) REPAIRING/REPLACING REAR WHEEL, TIRE/TUBE OPENING/CLOSING CLAMPS (FIGURE 6) DETERMINING TOE IN/TOE OUT (FIGURE 7) ADJUSTING TOE IN/TOE OUT FIGURE 9 - ADJUSTING TOE IN/TOE OUT - DEGREE OF CAMBER HAS BEEN CHANGED 9 OR 12 CAMBER Page FIGURE 10 - ADJUSTING TOE IN/TOE OUT - AXLE TUBE IS MOVED FROM FACTORY SET POSITION OR IS REPLACED T-3 ELITE AND T-4 MODELS WITH FIXED CAMBER (FIGURE 11) FIGURE 11 - ADJUSTING TOE IN/TOE OUT - T-3 ELITE MODELS WITH FIXED CAMBER ADJUSTING REAR WHEEL CAMBER (FIGURE 12) FIGURE 12 - REPOSITIONING CAMBER INSERTS (ADJUSTING REAR WHEEL CAMBER) ADJUSTING WHEELBASE LENGTH (ADJUSTING CENTER OF GRAVITY) (FIGURE 13) FIGURE 13 - ADJUSTING WHEELBASE LENGTH (ADJUSTING CENTER OF GRAVITY) DETAIL "A" - MEASURING FRAME BRACKET DISTANCE FIGURE 14 - ADJUSTING WHEELBASE WIDTH A-4 CAMBER TUBE CAMBER TUBE 2000 ADJUSTING WHEELBASE WIDTH (FIGURE 14) ADJUSTING WHEELBASE WIDTH - A-4 CAMBER TUBE ADJUSTING WHEELBASE WIDTH - CAMBER TUBE 2000 REPLACING AXLE TUBE (FIGURE 15) FIGURE 15 - REPLACING AXLE TUBE FRONT CASTER REPLACEMENT (FIGURE 17) FIGURE 17 - FRONT CASTER ADJUSTING FRONT CASTER HEIGHT (FIGURE 18) FIGURE 18 - ADJUSTING FRONT CASTER HEIGHT INSTALLING QUICK-RELEASE CASTERS (FIGURE 19) A NOTE ABOUT QUICK-RELEASE CASTERS FIGURE 19 - INSTALLING QUICK- RELEASE CASTERS WHEEL LOCK ADJUSTMENT/REPLACEMENT (FIGURE 20) REPLACING THE HIGH/LOW MOUNT WHEEL LOCK ADJUSTING THE HIGH/LOW MOUNT WHEEL LOCKS FIGURE 20 - WHEEL LOCK ADJUSTMENT/REPLACEMENT INSTALLING/USING/ADJUSTING THE FIXED FOOTREST - AFTER 4/2000 (FIGURE 1) INSTALLING/USING FOOTREST - T-3 ELITE, T-3 ADJUSTABLE, T-3 TITANIUM FIGURE 1 - INSTALLING/USING/ADJUSTING THE FIXED FOOTREST INSTALLING/USING FOOTREST - T-4 ELITE AND T-4 TITANIUM FIGURE 2 - INSTALLING/USING FOOTREST - T-4 ELITE AND T-4 TITANIUM PROCEDURE 7FOOTREST ADJUSTING FOOTREST HEIGHT ADJUSTMENT DEPTH ADJUSTMENT T-3 TENNIS ELITE INDIVIDUAL FOOTPLATES - BEFORE 4/2000 (FIGURES 2 AND 3) PROCEDURE 7FOOTREST CHANGING FOOTPLATE ANGLE CHANGING FOOTPLATE DEPTH CHANGING FOOTPLATE HEIGHT FIGURE 4 - T-3 TENNIS ELITE INDIVIDUAL FOOTPLATES - BEFORE 4/2000 REMOVING FOOTPLATE(S) INSTALLING FOOTPLATE(S) REMOVING FOOTPLATE SYSTEM MOUNTING CLAMP REPLACING FOOTPLATE MOUNTING BRACKET Page T-3 TENNIS ADJUSTABLE FOOTREST SYSTEM - BEFORE 4/2000 (FIGURE 4) ADJUSTING INDIVIDUAL FOOTPLATES REPLACING INDIVIDUAL FOOTPLATES FOOTREST PROCEDURE 7 REPLACING FOOTPLATE WELDMENT REPLACING SEAT ADJUSTMENT WELDMENT FIGURE 6 - T-3 TENNIS ADJUSTABLE FOOTREST SYSTEM - BEFORE 4/2000 REPLACING/ADJUSTING FIXED ANTI-TIPPER SWIVEL CASTER Page PROCEDURE 8OPTIONAL ANTI-TIPPER INSTALLING/ADJUSTING REMOVABLE ANTI-TIPPER T-3 ADJUSTABLE - AFTER 2001 (FIGURE 2) INSTALLING ADJUSTING OPTIONAL ANTI-TIPPER Page LIMITED WARRANTY WARRANTY WARRANTY