Manuals / Brands / Personal Care / Mobility Aid / Invacare / Personal Care / Mobility Aid

Invacare Top End T-3 RIGID CLOTHING GUARD REPLACEMENT (FIGURE 2), NYLON CLOTHING GUARD WITH PLASTIC INSERT REPLACEMENT (FIGURE 1)

1 64

Download 64 pages, 617.32 Kb

Part No. 1054916 29 T-3™ and T-4™ Series

RIGID CLOTHING GUARD REPLACEMENT (FIGURE 2)

1. Remove rear wheels if necessary. Refer to REMOVING/INSTALLING REAR WHEELS in

PROCEDURE 6 of this manual.

2. Remove seat cushion from chair.

3. Install the clothing guard clamps to the

chair as shown in FIGURE 2 with the

outer clamp located onto the outside of

the seat rail and the inner clamp on the

inside of the seat rail.

4. Assemble the clamps together with allen

screw and washer provided.

5. Adjust clamp assembly forward or rear-

ward to desired position.

6. Install rigid clothing guard by inserting

stem into clamp assembly.

7. Repeat steps for other side of chair.

NYLON CLOTHING GUARD WITH PLASTIC INSERTREPLACEMENT (FIGURE 1)

1. Lift up on the seat cushion and remove it

from the chair.

2. Separate the nylon clothing guard with

plastic insert from the seat and back

upholstery.

3. Install NEW nylon clothing guard with

plastic insert onto the seat and back

upholstery.

NOTE: The fastening flaps that secure the nylon

clothing guards to the back upholstery wrap around

the outside of the back canes.

4. Reattach the seat cushion to the seat

upholstery.

This Procedure includes the following:

Nylon Clothing Guard With Plastic Insert Replacement

Rigid Clothing Guard Replacement

PROCEDURE 5CLOTHING GUARDS

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure all attach-

ing hardware is tightened securely - otherwise injury or damage may result.

FIGURE 1 - NYLON CLOTHING

GUARD WITH PLASTIC INSERT

REPLACEMENT

Back Cane

Nylon Clothing Guard With

Plastic Insert

Fastening Flaps

FIGURE 2 - RIGID CLOTHING

GUARD REPLACEMENT

Rigid Clothing Guard

Inner Clamp

Seat Rail

Washer

Allen

Screw

Outer Clamp

Stem

CLOTHING GUARDS

Contents

Main SPECIAL NOTES NOTICE SPECIAL NOTES WARNING TABLE OF CONTENTS REGISTER YOUR PRODUCT! The benefits of registering: Register ONLINE at www.invacare.com - or - Complete and mail the form on the next page PRODUCT REGISTRATION FORM Page Page Page See current order form STABILITY STABILITY WARNINGS GENERAL GUIDELINES PROCEDURE 1 GENERAL GUIDELINES PROCEDURE 1 GENERAL WARNINGS (CONTINUTED) GENERAL WARNINGS (CONTINUTED) TIRE PRESSURE WEIGHT TRAINING WEIGHT LIMITATION SAFETY/HANDLING OF WHEELCHAIRS STABILITY AND BALANCE COPING WITH EVERYDAY OBSTACLES A NOTE TO WHEELCHAIR ASSISTANTS PERCENTAGE OF WEIGHT DISTRIBUTION PROCEDURE 1GENERAL GUIDELINES FUNCTIONAL REACH FROM A WHEELCHAIR TILTING STAIRWAYS GENERAL GUIDELINES PROCEDURE 1 TRANSFERRING TO AND FROM OTHER SEATS ESCALATORS? SORRY! SAFETY INSPECTION CHECKLIST SAFETY INSPECTION PROCEDURE 2 TROUBLESHOOTING SAFETY INSPECTIONPROCEDURE 2 SAFETY INSPECTION CHECKLIST (CONTINUED) MAINTENANCE SAFETY INSPECTION PROCEDURE 2 MAINTENANCE SAFETY PRECAUTIONS SUGGESTED MAINTENANCE PROCEDURES BACKPROCEDURE 3 ADJUSTING/REPLACING BACK UPHOLSTERY (FIGURE 1) ADJUSTING BACK UPHOLSTERY FIGURE 1 - ADJUSTING/REPLACING BACK UPHOLSTERY REPLACING BACK UPHOLSTERY PROCEDURE 3BACK FOLDING BACK (FIGURE 2) FIGURE 2 - FOLDING BACK BACK HEIGHT ADJUSTMENT (FIGURE 3) BACK PROCEDURE 3 FIGURE 3 - BACK HEIGHT ADJUSTMENT BACK ANGLE ADJUSTMENT (FIGURE 4) HOLE NUMBER FIGURE 4 - BACK ANGLE ADJUSTMENT 94 BACK ANGLE TO SEAT RAIL 90 BACK ANGLE TO SEAT RAIL 77 BACK ANGLE TO SEAT RAIL 73 BACK ANGLE TO SEAT RAIL SEAT UPHOLSTERY REPLACEMENT (FIGURE 1) FIGURE 1 - SEAT UPHOLSTERY REPLACEMENT REAR SEAT HEIGHT ADJUSTMENT FRONT SEAT HEIGHT ADJUSTMENT Before 2001 (FIGURE 4) After 2001 (FIGURE 5) PROCEDURE 4 SEAT FIGURE 4 - FRONT SEAT HEIGHT ADJUSTMENT - BEFORE 2001 RIGID CLOTHING GUARD REPLACEMENT (FIGURE 2) NYLON CLOTHING GUARD WITH PLASTIC INSERT REPLACEMENT (FIGURE 1) PROCEDURE 5CLOTHING GUARDS CLOTHING GUARDS FIGURE 1 - NYLON CLOTHING GUARD WITH PLASTIC INSERT REMOVING/INSTALLING REAR WHEELS (FIGURE 1) QUICK OR QUAD-RELEASE AXLES FIGURE 2 - ADJUSTING QUICK-RELEASE AXLES WHEELS PROCEDURE 6 ADJUSTING QUICK-RELEASE AXLES (FIGURE 2) FIGURE 1 - REMOVING/INSTALLING REAR WHEELS INSTALLING/ADJUSTING QUAD-RELEASE AXLES INSTALLING (FIGURE 3) FIGURE 3 - INSTALLING QUAD-RELEASE AXLES ADJUSTING (FIGURE 4) FIGURE 4 - ADJUSTING QUAD-RELEASE AXLES FIGURE 5 - HANDRIM HANDRIM REPLACEMENT (FIGURE 5) REPAIRING/REPLACING REAR WHEEL, TIRE/TUBE OPENING/CLOSING CLAMPS (FIGURE 6) DETERMINING TOE IN/TOE OUT (FIGURE 7) ADJUSTING TOE IN/TOE OUT FIGURE 9 - ADJUSTING TOE IN/TOE OUT - DEGREE OF CAMBER HAS BEEN CHANGED 9 OR 12 CAMBER Page FIGURE 10 - ADJUSTING TOE IN/TOE OUT - AXLE TUBE IS MOVED FROM FACTORY SET POSITION OR IS REPLACED T-3 ELITE AND T-4 MODELS WITH FIXED CAMBER (FIGURE 11) FIGURE 11 - ADJUSTING TOE IN/TOE OUT - T-3 ELITE MODELS WITH FIXED CAMBER ADJUSTING REAR WHEEL CAMBER (FIGURE 12) FIGURE 12 - REPOSITIONING CAMBER INSERTS (ADJUSTING REAR WHEEL CAMBER) ADJUSTING WHEELBASE LENGTH (ADJUSTING CENTER OF GRAVITY) (FIGURE 13) FIGURE 13 - ADJUSTING WHEELBASE LENGTH (ADJUSTING CENTER OF GRAVITY) DETAIL "A" - MEASURING FRAME BRACKET DISTANCE FIGURE 14 - ADJUSTING WHEELBASE WIDTH A-4 CAMBER TUBE CAMBER TUBE 2000 ADJUSTING WHEELBASE WIDTH (FIGURE 14) ADJUSTING WHEELBASE WIDTH - A-4 CAMBER TUBE ADJUSTING WHEELBASE WIDTH - CAMBER TUBE 2000 REPLACING AXLE TUBE (FIGURE 15) FIGURE 15 - REPLACING AXLE TUBE FRONT CASTER REPLACEMENT (FIGURE 17) FIGURE 17 - FRONT CASTER ADJUSTING FRONT CASTER HEIGHT (FIGURE 18) FIGURE 18 - ADJUSTING FRONT CASTER HEIGHT INSTALLING QUICK-RELEASE CASTERS (FIGURE 19) A NOTE ABOUT QUICK-RELEASE CASTERS FIGURE 19 - INSTALLING QUICK- RELEASE CASTERS WHEEL LOCK ADJUSTMENT/REPLACEMENT (FIGURE 20) REPLACING THE HIGH/LOW MOUNT WHEEL LOCK ADJUSTING THE HIGH/LOW MOUNT WHEEL LOCKS FIGURE 20 - WHEEL LOCK ADJUSTMENT/REPLACEMENT INSTALLING/USING/ADJUSTING THE FIXED FOOTREST - AFTER 4/2000 (FIGURE 1) INSTALLING/USING FOOTREST - T-3 ELITE, T-3 ADJUSTABLE, T-3 TITANIUM FIGURE 1 - INSTALLING/USING/ADJUSTING THE FIXED FOOTREST INSTALLING/USING FOOTREST - T-4 ELITE AND T-4 TITANIUM FIGURE 2 - INSTALLING/USING FOOTREST - T-4 ELITE AND T-4 TITANIUM PROCEDURE 7FOOTREST ADJUSTING FOOTREST HEIGHT ADJUSTMENT DEPTH ADJUSTMENT T-3 TENNIS ELITE INDIVIDUAL FOOTPLATES - BEFORE 4/2000 (FIGURES 2 AND 3) PROCEDURE 7FOOTREST CHANGING FOOTPLATE ANGLE CHANGING FOOTPLATE DEPTH CHANGING FOOTPLATE HEIGHT FIGURE 4 - T-3 TENNIS ELITE INDIVIDUAL FOOTPLATES - BEFORE 4/2000 REMOVING FOOTPLATE(S) INSTALLING FOOTPLATE(S) REMOVING FOOTPLATE SYSTEM MOUNTING CLAMP REPLACING FOOTPLATE MOUNTING BRACKET Page T-3 TENNIS ADJUSTABLE FOOTREST SYSTEM - BEFORE 4/2000 (FIGURE 4) ADJUSTING INDIVIDUAL FOOTPLATES REPLACING INDIVIDUAL FOOTPLATES FOOTREST PROCEDURE 7 REPLACING FOOTPLATE WELDMENT REPLACING SEAT ADJUSTMENT WELDMENT FIGURE 6 - T-3 TENNIS ADJUSTABLE FOOTREST SYSTEM - BEFORE 4/2000 REPLACING/ADJUSTING FIXED ANTI-TIPPER SWIVEL CASTER Page PROCEDURE 8OPTIONAL ANTI-TIPPER INSTALLING/ADJUSTING REMOVABLE ANTI-TIPPER T-3 ADJUSTABLE - AFTER 2001 (FIGURE 2) INSTALLING ADJUSTING OPTIONAL ANTI-TIPPER Page LIMITED WARRANTY WARRANTY WARRANTY