JVC BR-HD50 manual Event/Alarm display, Display displayed during operation Description

ON-SCREEN DISPLAY

Event/Alarm display

„Event display : When certain functions are in use, it is displayed at the following posi- tions (with the DISPLAY mode ON or AUTO).

z“B” display:Messages for incorrect operation are displayed for about 3 seconds. They are displayed when the DISPLAY mode is ON or AUTO.

	D V 3 2 K C H – 1 / 2				S P	2 0 m i n
A
			B L A N K S E A R C H
B
		I N D E X D E T E C T E D
	0 6 / 1 0 / 0 5			S T A N D B Y -O F F
	1 1 : 2 0 : 0 0		T C R 0 2 : 0 0 : 0 0 : 0 0

z“A” display: displayed during operation

Display	Description
BLANK	Blank search in progress.
SEARCH
INDEX +1	Index search in progress.
	The number indicates the
	index search position.
INDEX MARK	When an index has been
	specified on the tape during
	recording.

z“B” display: displayed for about 3 seconds

Display	Description
INVALID TAPE!	Data tape for PCs or DVC PRO tape is used.
	The cassette tape will be automatically ejected.
LP TAPE!	The user attempted to play back a tape recorded in the LP mode.
	BR-HD50 cannot record or play in the LP mode.
NO HDV/DV SIG- The user attempted to record without HDV or DV signal input.
NAL
COPY INHIBIT	The user attempted to record copy-guarded signals.
REC INHIBIT	The user attempted to record on a tape that is not ready for recording (the rear
	switch is set to SAVE).
OPERATION	This message is displayed when an operation button is pressed with OPERAION

Display	Description
INDEX	An index has been detected
DETECTED	during index repeat operation.
VIDEO END	The video end has been
DETECTED	detected during end repeat
	operation.

„Alarm display : An alarm message is displayed at the following positions when there has been an operation error or when BR-HD50 is not in good condition, e.g., dirty head.

							2 0 m i n
	D V 3 2 K C H – 1 / 2					S P
A
		H E A D C L E A N I N G R E Q U I R E D !
B
			N O H D V / D V S I G N A L
	0 6 / 1 0 / 0 5				S T A N D B Y -O F F
	1 1 : 2 0 : 0 0			T C R 0 2 : 0 0 : 0 0 : 0 0

z“A” display: The state of BR-HD50 is displayed. It continues to be displayed until the error state is corrected. This display is not affected by the setting of the display mode.

Display	Description
LOW VOLTAGE	The voltage of the DC power source is low. If the operation continues, it enters
	the OPERATE OFF mode.
HEAD CLEANING	The video head is dirty. Clean it with the head-cleaning tape exclusively for BR-
REQUIRED!	HD50. (XPage 9)
	If the head is clogged, it is detected in the PLAYBACK mode and this message is
	displayed.
OVERHEATING!	The temperature inside BR-HD50 has exceeded the stated value.
	Disconnect the power and place it at a cool place. If this message is displayed
	again, BR-HD50 could be defective.
	Consult your JVC-authorized service agent.

LOCK	LOCK enabled. To enable OPERATION LOCK, set OPERATION LOCK in the
	SYSTEM [2/2] Menu screen to ON.
PB INHIBIT	This message is displayed when the HD/SD signal format setting differs during
[60/50]	playback of a tape recorded in HDV/DV format.
REC INHIBIT	•	(for U model)
[60/50]		This message is displayed when the unit is recorded in PAL mode.
	•	(for E model)
		This message is displayed when the unit is recorded in NTSC mode.
50/25 INHIBIT	• When 60/50 SEL in the SYSTEM [2/2] Menu screen is set to 60, this message
		is displayed when HDV signal format is not 60Hz.
	• This message is displayed when the DV signal from the IEEE1394 terminal is
		not NTSC.
60/30 INHIBIT	• When 60/50 SEL in the SYSTEM [2/2] Menu screen is set to 50, this message
		is displayed when HDV signal format is not 50Hz.
	• This message is displayed when the DV signal from the IEEE1394 terminal is
		not PAL.

E-24 E-25