JVC DLA-M4000LU Basic Operations, When Turning On the Devices Connected to the Projector

No.51666

Connecting to Various Devices (Cont.)

When Turning On the Devices Connected to the Projector

Turn on the switches of the projector and the devices connected in the following order.

Skip over unconnected devices if there is any.

Power switch of the monitor of the computer which provides input to the projector

Peripheral devices of the computer which provides input to the projector (Hard disk, magneto optical disk, scanner, etc.)

Power switch of AV devices which provide input to the projector

Projector itself

Power switches of devices to which the projector provides output

(AV devices and display monitor)

Power switch of the computer which provides input to the projector

* When turning off the power switches, do so in the reverse order.

CAUTIONS and NOTES

Do not turn off the MAIN POWER switch suddenly while the projector is being used or immediately after it has been used. This could cause a malfunction.

•Since the projector uses a high-intensity lamp and is heated to high temperature, cooling fans are operating even during projection. So, after use, the cooling fans continue to run until the light-source lamp is sufficiently cooled down after the OPERATE button was pressed. During the cooling-down, never turn off the main power switch. Turn it off only after the cooling fans (except the one for the light-source lamp power supply) have stopped running.

(The cooling fans will run for about 10 minutes after the STAND BY indicator has changed from flashing (for about 20 seconds) to steady lighting.)

•If you press the OPERATE button immediately after the light-source lamp lights, it takes about 30 seconds for the lamp to go off. To turn the lamp on again, wait 20 seconds or more before pressing the OPERATE button.

When the TEMP indicator lights, the power turns off automatically.

•While the light-source lamp is on, if an abnormal temperature rise is detected, the TEMP indicator comes on, the power is automatically cut off, and the projector’s EMERGENCY indicator blinks (goes into an emergency mode).

When the EMERGENCY indicator blinks, turn off the main power switch after the fans have stopped running.

•If the following abnormality occur to the projector, it goes into an emergency mode (the EMERGENCY indicator blinks). When the projector goes into an emergency mode, it stops projecting automatically and the cooling fans will continue to run for about 10 minutes more before they stop (except the cooling fan for the light-source lamp power supply which continues running as long as the MAIN POWER switch is on).

–When the fans stop running.

–When the temperature inside rises abnormally high.

•When the projector goes into an emergency mode:

After the fans have stopped, turn off the MAIN POWER switch and pull out the power cord. After that, re-insert the power cord and try to operate the projector. If it goes into emergency again, after the fans have stopped, turn off the main power switch, pull out the power cord, and consult your authorized dealer or service center for repair.

24

Basic Operations

■Projector’s buttons

STAND BY indicator

OPERATE indicator

TEMP

STAND BY OPERATE LAMP EMERGENCY AV RGB

OPERATE button 2, 1

MAIN POWER switch 1, 2

■Remote control unit

QUICK
ALIGN.	OPERATE	OPERATE button
	AV HIDE
PRESET	PAGE BACK	2, 1
LENS LOCK	N
	M
	EN
	U/
UNLOCK	E
	T
	E
	R

AV RGB/COMPUTER

U T +

SHIFT ZOOM FOCUS

D W –

LENS

The following describes the basic procedure for normal use of the projector.

1.Turning on the Power

1 Turn on the MAIN POWER switch of the projector.

ON [ ❙ ]:The main power turns on and the STAND BY indicator comes on.

Projector’s indicator

STAND BY

2Press the OPERATE button for one second or more.

(Or press the remote control’s OPERATE button for one second or more.)

•The OPERATE indicator comes on.

•About 30 seconds after the MAIN POWER switch is turned on, you can start projecting.

Remote control unit Projector

OPERATE

or

OPERATE

Note

•After the power is turned on, the screen may be jumbled for a few seconds, but this is not a malfunction.

■Turning off the Power

1Press the OPERATE button for one second or more.

(Or press the remote control’s OPERATE button for one second or more.)

•The STAND BY indicator changes to blinking, and the projector goes into cool-down mode.

Example of the projector’s button Projector

\

STAND BY

OPERATE

2Turn off the MAIN POWER switch after the cooling fans have

stopped running.

OFF [‡]: The MAIN POWER switch turns off and the STAND BY indicator goes off.

Projector

STAND BY

*Do not turn off the MAIN POWER switch during cool down mode (the STAND BY indicator blinking). About 10 minutes after the STAND BY indicator comes on steady (stand-by mode), the cooling fans (except the one for the light-source lamp power supply) will stop, and then turn off the MAIN POWER switch.

25

DLA-M4000LU DLA-M4000LE