Masterpage:Right+
EN 39
Filename [M150SEK_07Timer Recording.fm]
TIMER RECORDING
On-Disc Timer Programming is a function used with discs that are
especially intended for a specific programme. The disc is then
programmed for a programme you always watch every day or
every week. Since older programmes are automatically
overwritten, a single disc can be used without worrying about how
much recording capacity remains. You can programme each disc
to timer record as many as 8 programmes up to 30 days in
advance.

To Make The Disc For On-Disc Timer Programming

1Press PROG to access
the Programme Check
screen.
2Press selection keys to
select ADISC TIMER
PRGMB, then press
ENTER.
●When some
programmes are
recorded on the disc, a
caution message
appears. You can either format the disc (Apg. 67) or insert a
new disc, then re-perform the procedure from step 1.
●When On-Disc Timer Programming has already been made on
the disc, press selection keys to select ANEW TIMER
PROGRAMMEB, then press ENTER.
3Press selection keys to
set the desired date
(ADATEB), then press E.
4Press selection keys to
set the desired start time
(ASTARTB), then press E.
●Each press of FG
increases/decreases the
start time in 1 minute
interval.
●To increase/decrease the
start time in 30 minutes interval, press and hold FG.
5Press selection keys to set the desired stop time (ASTOPB),
then press E.
●Each press of FG increases/decreases the stop time in
1 minute interval.
●To increase/decrease the stop time in 30 minutes interval, press
and hold FG.
6Press selection keys to set the desired channel (ATV PROGB),
then press E.
7Press selection keys to set ADAILY/WEEKLYB, then press E.
●For details on ADAILY/WEEKLYB setting, refer to ADaily/Weekly
Recording FunctionB (Apg. 37).
8Set the other recording
options as required.
●ARecording ModeB
(Apg. 34)
●AModify Title NameB
(Apg. 46)
9Press ENTER to access
the Programme
Confirmation screen.
10 Press ENTER to
complete ATo Make The Disc For On-Disc Timer
ProgrammingB.
●To programme another timer using ATo Make The Disc For On-
Disc Timer ProgrammingB, repeat steps 1-10.
11 Press DVD A to turn off the power.
● is displayed on the front display panel.
●To disengage the timer mode, press DVD A again.

On-Disc Timer Programming

●Make sure that the unit’s built-in clock is set properly.
●Turn on the TV and select an input mode such as EXT1.
●Load a DVD-RAM or DVD-RW (VR mode) disc for
programming.
●Slide the TV/DVD switch to DVD.
ATTENTION:
●On-Disc Timer Programming is possible only with the disc for
On-Disc Timer Programming.
●If data is recorded on a disc for On-Disc Timer Programming
using a unit from another manufacturer, On-Disc Timer
Programming may not function properly.
●If timer programming cannot be set or cancelled, wait for about
40 seconds and then try again.
(FGDE)
ENTER
PROG
DVD A
AUX
DVD
TV
Selection Keys
Satellite Receiver Users
To timer record a satellite broadcast using On-Disc Timer
Programming:
APerform On-Disc Timer Programming.
●In step 6, press AUX to set ATV PROGB to ASATB. Then press
FG to enter the channel position for the satellite broadcast.
BSet the satellite receiver to the appropriate channel for
recording.
●Leave the satellite receiver’s power on.
PROGRAMME CHECK
DISC TIMER PRGM
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
OK
SELECT
PROG
EXIT
++++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++++
DATE
START
TV PROG
REC MODE
DAILY/WEEKLY
STOP
LP
DISC TIMER PRGM
DATE
START
STOP TV PROG
05/07 SAT
DAILY/WEEKLY
NAME
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
WEEKLY
REC MODE
CONFIRM
SELECT
PROG
EXIT
LP
YORN 120:3018:30
DISC TIMER PRGM
DATE
START
STOP TV PROG
05/07 SAT
DAILY/WEEKLY
NAME
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
WEEKLY
REC MODE
CONFIRM
SELECT
PROG
EXIT
M150SEK_00.book Page 39 Wednesday, June 15, 2005 4:04 PM