JVC DR-MV5S manual Mode Set VHS Deck, VHS Enter, For Example

Mode Set (VHS Deck)

SUBSIDIARY SETTINGS EN 75

* The boldface settings below indicate the settings at your purchase.

8 VHS]DVD DUBBING — 1 PROG / TAPE END

●Turn on the unit.

●Turn on the TV and select the AV mode.

●Slide the TV/DVD switch to DVD.

VHS

ENTER

rtwe

Set to the appropriate mode when you perform the dubbing from VHS tape to DVD disc. For details, refer to page 37 –38.

1 PROG: Dubbing stops when the unit decodes the index code (VISS signal).

TAPE END: Dubbing stops when the end of the tape reached.

8VIDEO CALIBRATION — ON / OFF

You can set the Video Calibration to “ON” or “OFF”.

NOTES:

●When watching a tape recorded with “VIDEO CALIBRATION” set to “ON”, it is recommended that you leave “VIDEO CALIBRATION” on during playback as well.

●When watching a rental tape or one recorded on another video recorder, or when using this unit as the player for editing, set “VIDEO CALIBRATION” to your preference.

●The Video Calibration works for both SP and EP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

●The Video Calibration does not work while Automatic Satellite Program Recording is in progress. ( pg. 36) In the case of timer recordings, the Video Calibration works before recording is initiated.

●Once the cassette is ejected, the Video Calibration data is cancelled. The next time the cassette is used for recording, Video Calibration is re-performed.

8AUTO SP]EP TIMER — ON / OFF

When this function is set to “ON”, the unit automatically switches to EP mode to allow complete recording if there is not enough tape to record the entire program while timer-recording in SP mode.

For Example:

Recording a program of 140 minutes in length onto a 120-minute tape.

SET UP

Various modes of this unit are categorized into menus nested in 2 levels shown in the following table. To change the settings of these modes, find the desired mode in the menu (for details on each menu, see pages 75 through 76), then follow the procedure below.

VHS SET UP	( pg. 75 – 76)
FUNCTION SET UP*	VIDEO IN/OUT ( pg. 23, 73)
* Common settings with DVD	RECORDING SET ( pg. 73)
	DISPLAY SET ( pg. 73)
deck
	OTHERS ( pg. 74)
INITIAL SET UP*	TUNER SET ( pg. 22)
* Common settings with DVD	CLOCK SET ( pg. 21)
deck

●The procedure below shows how to set the desired option of the “VIDEO CALIBRATION” mode as an example.

1 Press VHS so that the VHS lamp lights up on the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “VHS SET UP”, then press t.
4 Press rt to select “VIDEO	VHS SET UP	FUNCTION SET UP		INITIAL SET UP
CALIBRATION”, then press
ENTER.	VHS ] DVD DUBBING			TAPE END
5 Press rt to select the desired	VIDEO CALIBRATION			OFF OFF
	AUDIO SP ] EP TIMER			ON
option, then press ENTER.	VIDEO STABILIZER			OFF
6 Press SET UP to complete the	PICTURE COUNTROL			AUTO
	SET UP	OK
setting.			SELECT WITH [CURSORS]
	EXIT	SELECT	THEN PRESS [ENTER]

Approximately 110 minutes	Approximately 30 minutes
SP mode	EP mode

Total 140 minutes

Make sure you set this function to “ON”, before the timer-recording starts.

NOTES:

●If you have programed the unit to timer-record 2 or more programs, the second program and those thereafter may not fit on the tape if you set “AUTO SP]EP TIMER” to “ON”. In this case, make sure the mode is not engaged, then set the tape speed manually during timer programing.

●In order to ensure that the recording fits on the tape, this feature may leave a slight non-recorded section at the end of the tape.

●There may be some noise and sound disturbance at the point on the tape where the unit switches from SP to EP mode.

●The “AUTO SP]EP TIMER” feature is not available during ITR (Instant Timer Recording), and the feature will not work properly on the following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.