Name and Function of Parts | JVC LWT0254-001B-H specification

Introduction (continued)	7
EN

Name and Function of Parts

8Ceiling Mount (Terminal Side)

I

A

B

C

H

G

F

E

D

ASafety Wire

Hang this wire to the Fastening Hook for Safety Wire S.

B[VIDEO OUT] Coaxial Cable Terminal

Output terminal of a composite video signal (1 V(p-p)) with an output impedance of 75 K, to be connected to a switcher, etc.

C[AC24V H INPUT] AC 24 V Input Terminal Connect to a AC 24 V power supply.

DSafety Wire Mounting Hole

To prevent the camera from falling down, pass the wire from the ceiling slab or channel to this hole.

E[ALARM IN / OUT] Alarm Input/Output Terminals (J502) Terminals for alarm input and output. (A pg. 17)

Pin No.	Signal Name	Displayed As

1	Alarm Output +	OUT +

2	Alarm Output -	OUT -

3	Alarm Input	IN

4	GND	GND

5	^	RESERVED

FLocking Screw

For fastening the camera body. Ensure to fasten the Camera Clamping Bracket P using this screw.

G[CONTROL] Control Signal Terminal (J501) Connect this to the remote control unit (RM-P2580).

Pin No.	Signal Name	Displayed As
1	TX +
2	TX -
3	RX +
4	RX -

HCover

This is a protection cover. Cut a slit in the rubber cap attached to the cover when wiring cables. When connecting cables to the ceiling mount, ensure to do so by running the cables through the Cover H. (A pg. 16)

ICover Fastening Screw

This is used for fastening the Cover H and the ceiling mount.

To remove Cover H, do so by unfastening this screw.

Image 7

JVC LWT0254-001B-H manual Name and Function of Parts

Contents

Model No. TK-C625 Serial No LWT0254-001B-H For Customer Use Risk of Electric Shock Do not Open Safety PrecautionsInformation Important Safeguards Contents Characteristics Operating Precautions → Refer to Preset positionsZooming operation Name and Function of Parts Auxiliary Switch Ceiling Mount Setting Switch Side CameraMachine ID Machine ID Setting Switch Setting Switch Multi-Drop Communication System Connections & Installation CAM2 Length of stub CAM32 Length of stub Video SWITCHER, etc110 K ACable ConnectionsB a pg Terminal side of the Ceiling Mount Point-to-Point Communication System Example connection with an RM-P2580 DuplexSimplex Protocol Switch SettingsSync Displayed as ID- LL. Check Machine ID Setting Switch Machine ID Installation Lead the cable through the Cover Cable ConnectionsMake a hole in the ceiling Connect the cable to this camera Remove the Cover Rating Connecting an RG-59 coaxial cablePolyethylene Mesh Wires Core Wire Cable Within 10 cm Connect this to the remote control unit RM-P2580Connect to an AC 24 V Supply Cable Attach the Safety Wire Installing the Ceiling MountFasten the ceiling mount to the ceiling 20 EN Installing the Camera Press the SET button Setup ProcedureSetting Up the Camera Using RM-P258021 Press and hold the Menu button for 3 seconds Setting Up the Camera Using RM-P2580 Menu Screen Configuration22 EN Private Mask Mode OFF Camera Function 1 Screen 24 ENCamera Function 2 Screen Auto Return AF for IRTilt Limit PAN Limit 26 EN Camera TITLE/ALARM Screen Camera ALC/VIDEO Screen Auto PAN/PATROL/TRACE Screen 28 EN POS. Function SET Screen 30 EN Factory Settings Screen Private Mask Setup Set the position for the left limit Manual PAN Limit SetupSelect a camera. ARM-P2580 Ainstructionsb Menu screen display. a pg , steps 2 to Right Limit Settings that override the Manual Pan LimitBasic operation of Manual Pan Limit Operations that override the Manual Pan Limit Space Blinking Character area Camera Title SetupTele Numeric Enter Button keys button Wide button Menu Screen Menu button Area Display Setup TitlePress the FAR button Repeat Steps 5 to Camera button Area Display Setup DirectionEast West Repeat steps 5 to 7 for each alarm title Alarm Title SetupCamera buttonNNumeric keyCamera NumberNENTER button Select camera. ARM-P2580 Ainstructionsb Auto PAN SetupSet the Auto PAN Mode and Auto PAN Speed Set the end position only when in the Return mode Set the length of time a camera will stay in each position Auto Patrol SetupChange the Auto Patrol mode Set a patroll position To Start Auto Trace Function Auto Trace SetupSet the patrol start position Camera buttonNNumeric key Camera Number Nenter button Position buttonNNumeric key position numberNENTER button Position Title SetupSelect a preset position. a RM-P2580 Ainstructionsb Repeat steps 5 to 7 for each title character 42 EN TroubleshootingOther General SpecificationsExternal Dimensions Unit mm Pan/Tilt Mechanism Victor Company of Japan, Limited