Switch Settings, Protocol, Sync | JVC LWT0254-001B-H specs

Connections & Installation (continued)	13
EN

Switch Settings

Set the switches on the Ceiling Mount before installing the camera. Settings vary according to configuration of the system used.

8Setting switches

Setting not required.

Set all to OFF.

AMachine ID Setting SwitchB (A pg. 14)

Switch 1 :	Invalid (Set to OFF)
Switch 2 :	Invalid (Set to OFF)
Switch 3 :	Invalid (Set to OFF)
Switch 4 :	PROTOCOL(1)
Switch 5 :	PROTOCOL(2)
Switch 6 :	SYNC
Switch 7 :	Invalid (Set to OFF)
Switch 8 :	RX TERM

ON
1	2	3	4	5	6	7	8

RRESERVED (Switches 1, 2, 3) These switches must be set to OFF.

RPROTOCOL (1) (Switch 4)

Selects whether a single camera or multiple cameras are controlled in a system.

Set PROTOCOL(1) to Multi drop when connecting multiple cameras in series.

PROTOCOL (1)	Switch 4

Point-to-point		OFF

Multi-drop (when using the RM-P2580)		ON

(Initial setting: OFF)

When set to Multi-drop, be sure to set the Machine ID of each camera.

RPROTOCOL (2) (Switch 5)

Set this switch according to the communication protocol used when controlling the cameras.

	PROTOCOL (2)	Switch 5

	Duplex (when using the RM-P2580)		OFF

	Simplex		ON

	(Initial setting: OFF)

RSYNC (Switch 6)

When this switch is set to ON, the vertical sync of the camera becomes locked to the frequency of the AC power line.

SYNC	Switch 6

INT		OFF

LL		ON

(Initial setting: OFF)

(LL mode : TK-C625E : 50Hz ONLY TK-C625U : 60Hz ONLY)

RRESERVED (Switch 7)

This switch must be set to OFF.

RRX TERM (Switch 8)

This switch sets whether or not the section between control signal terminals RX + and RX - is to be terminated (with a resistance of 110 K).

	RX Termination			Switch 8

	Terminated (110 K)				ON


	Open				OFF

	(Initial setting: Terminated (110 K))

When the system in which this camera is used is a multidrop system (RS-485 system), set only the camera located at the extreme end of the control signal cables to ATerminatedB and set the other cameras to AOpenB.

Image 13

JVC LWT0254-001B-H manual Switch Settings, Protocol, Sync

Contents

Model No. TK-C625 Serial No LWT0254-001B-H For Customer Use Risk of Electric Shock Do not Open Safety PrecautionsInformation Important Safeguards Contents Characteristics Operating Precautions → Refer to Preset positionsZooming operation Name and Function of Parts Machine ID Machine ID Setting Switch Ceiling Mount Setting Switch Side CameraSetting Switch Auxiliary Switch Multi-Drop Communication System Connections & Installation CAM2 Length of stub CAM32 Length of stub Video SWITCHER, etc110 K ACable ConnectionsB a pg Terminal side of the Ceiling Mount Point-to-Point Communication System Example connection with an RM-P2580 DuplexSimplex Protocol Switch SettingsSync Displayed as ID- LL. Check Machine ID Setting Switch Machine ID Installation Make a hole in the ceiling Connect the cable to this camera Cable ConnectionsRemove the Cover Lead the cable through the Cover Polyethylene Mesh Wires Core Wire Connecting an RG-59 coaxial cableCable Rating Connect to an AC 24 V Supply Connect this to the remote control unit RM-P2580Cable Within 10 cm Attach the Safety Wire Installing the Ceiling MountFasten the ceiling mount to the ceiling 20 EN Installing the Camera Setting Up the Camera Using RM-P258021 Setup ProcedurePress and hold the Menu button for 3 seconds Press the SET button Setting Up the Camera Using RM-P2580 Menu Screen Configuration22 EN Private Mask Mode OFF Camera Function 1 Screen 24 ENCamera Function 2 Screen Tilt Limit AF for IRPAN Limit Auto Return 26 EN Camera TITLE/ALARM Screen Camera ALC/VIDEO Screen Auto PAN/PATROL/TRACE Screen 28 EN POS. Function SET Screen 30 EN Factory Settings Screen Private Mask Setup Select a camera. ARM-P2580 Ainstructionsb Manual PAN Limit SetupMenu screen display. a pg , steps 2 to Set the position for the left limit Basic operation of Manual Pan Limit Settings that override the Manual Pan LimitOperations that override the Manual Pan Limit Right Limit Tele Numeric Enter Button keys button Wide button Camera Title SetupMenu Screen Space Blinking Character area Press the FAR button Area Display Setup TitleRepeat Steps 5 to Menu button East Area Display Setup DirectionWest Camera button Repeat steps 5 to 7 for each alarm title Alarm Title SetupCamera buttonNNumeric keyCamera NumberNENTER button Set the Auto PAN Mode and Auto PAN Speed Auto PAN SetupSet the end position only when in the Return mode Select camera. ARM-P2580 Ainstructionsb Change the Auto Patrol mode Auto Patrol SetupSet a patroll position Set the length of time a camera will stay in each position Set the patrol start position Auto Trace SetupCamera buttonNNumeric key Camera Number Nenter button To Start Auto Trace Function Select a preset position. a RM-P2580 Ainstructionsb Position Title SetupRepeat steps 5 to 7 for each title character Position buttonNNumeric key position numberNENTER button 42 EN TroubleshootingOther External Dimensions Unit mm SpecificationsPan/Tilt Mechanism General Victor Company of Japan, Limited