Point-to-Point Communication System | JVC LWT0254-001B-H instruction

Connections & Installation (continued)	11
EN

Point-to-Point Communication System

The following illustration shows a system in which a remote control unit (or a similar piece of equipment)

controls a single camera.

Video out

Control signal cable

AC 24 V power supply

(A CAUTIONS)

Switch 4 : OFF (Point to Point) Switch 8 : ON (Terminated 110 K)

Monitor

Controller

Observe the following points when connecting components together:

●Turn all the components off before proceeding.

●Read the instruction manuals of all components before proceeding.

8ACable ConnectionsB (A pg. 16) (Terminal side of the Ceiling Mount)

Control signal cable

To controller

Coaxial cable

To monitor

To the AC 24V power

supply. Listed class 2

Power cable input only.

(A CAUTIONS)

8ASwitch SettingsB (A pg. 13)

(Setting switches are on the side of the Ceiling Mount)

Setting not
required	ON

1 2 3 4 5 6 7 8

Switch 1 : Invalid (Set to OFF)

Switch 2 : Invalid (Set to OFF)

Switch 3 : Invalid (Set to OFF)

Switch 4 : OFF

Switch 5 : Configure in accordance with the requirements of the controller communication system.

Switch 7 : Invalid (Set to OFF)

Switch 8 : ON

MEMO

●If this camera or the cables connected to this camera are used in places subject to strong electromagnetic waves or other forms of magnetism, such as those near a radio or TV transmitter, a power transformer or an electric motor, the picture may suffer from noise and colors may be affected.

●An optionally available controller is required to use a TK-C625 camera. Please contact your local dealer or installer for more information about these controllers.

CAUTIONS

●The AC 24 V power supply must be isolated from the primary line. (ISOLATED POWER ONLY)

●In order to prevent an excessive current flow through the power supply wire or camera due to a short circuit, a fuse must be installed in the power supply line.

Image 11

JVC LWT0254-001B-H manual Point-to-Point Communication System, ACable ConnectionsB a pg Terminal side of the Ceiling Mount

Contents

Model No. TK-C625 Serial No LWT0254-001B-H For Customer Use Information Safety PrecautionsRisk of Electric Shock Do not Open Important Safeguards Contents Characteristics Operating Precautions Zooming operation Preset positions→ Refer to Name and Function of Parts Auxiliary Switch Ceiling Mount Setting Switch Side CameraMachine ID Machine ID Setting Switch Setting Switch Multi-Drop Communication System Connections & Installation 110 K Video SWITCHER, etcCAM2 Length of stub CAM32 Length of stub ACable ConnectionsB a pg Terminal side of the Ceiling Mount Point-to-Point Communication System Simplex DuplexExample connection with an RM-P2580 Sync Switch SettingsProtocol Displayed as ID- LL. Check Machine ID Setting Switch Machine ID Installation Lead the cable through the Cover Cable ConnectionsMake a hole in the ceiling Connect the cable to this camera Remove the Cover Rating Connecting an RG-59 coaxial cablePolyethylene Mesh Wires Core Wire Cable Within 10 cm Connect this to the remote control unit RM-P2580Connect to an AC 24 V Supply Cable Fasten the ceiling mount to the ceiling Installing the Ceiling MountAttach the Safety Wire 20 EN Installing the Camera Press the SET button Setup ProcedureSetting Up the Camera Using RM-P258021 Press and hold the Menu button for 3 seconds 22 EN Menu Screen ConfigurationSetting Up the Camera Using RM-P2580 Private Mask Mode OFF Camera Function 2 Screen 24 ENCamera Function 1 Screen Auto Return AF for IRTilt Limit PAN Limit 26 EN Camera TITLE/ALARM Screen Camera ALC/VIDEO Screen Auto PAN/PATROL/TRACE Screen 28 EN POS. Function SET Screen 30 EN Factory Settings Screen Private Mask Setup Set the position for the left limit Manual PAN Limit SetupSelect a camera. ARM-P2580 Ainstructionsb Menu screen display. a pg , steps 2 to Right Limit Settings that override the Manual Pan LimitBasic operation of Manual Pan Limit Operations that override the Manual Pan Limit Space Blinking Character area Camera Title SetupTele Numeric Enter Button keys button Wide button Menu Screen Menu button Area Display Setup TitlePress the FAR button Repeat Steps 5 to Camera button Area Display Setup DirectionEast West Camera buttonNNumeric keyCamera NumberNENTER button Alarm Title SetupRepeat steps 5 to 7 for each alarm title Select camera. ARM-P2580 Ainstructionsb Auto PAN SetupSet the Auto PAN Mode and Auto PAN Speed Set the end position only when in the Return mode Set the length of time a camera will stay in each position Auto Patrol SetupChange the Auto Patrol mode Set a patroll position To Start Auto Trace Function Auto Trace SetupSet the patrol start position Camera buttonNNumeric key Camera Number Nenter button Position buttonNNumeric key position numberNENTER button Position Title SetupSelect a preset position. a RM-P2580 Ainstructionsb Repeat steps 5 to 7 for each title character Other Troubleshooting42 EN General SpecificationsExternal Dimensions Unit mm Pan/Tilt Mechanism Victor Company of Japan, Limited