Preparation (Step 1 Connection/Installation)

1-2 Mounting the Camera to the Ceiling (Continued)

2. Installation (Continued)

3. Adjustment of the camera’s angle of view

 Connection of the Input Power Cable

Be careful of the following items when connecting the cables.

• Turn OFF the power supply to all components before making connections.

Setting

1.Connection for Adjustment of the

Camera

The MONITOR terminal is used when mak-

ing various adjustments to the camera at

To video Signal Cable

 DC 12 V or AC 24 V Input power cable

Connect the DC 12 V or the AC 24 V power

supply to the DC 12 V/AC 24 V terminals on

switch

Adjustment button

installation.

To DC 12 V or AC 24 V Power Supply

the terminal board. To prevent connection er-

rors or a cable disconnection, we recommend

the use of lug plates for the connections.

The following table shows the connection dis-

tances and connection cables provided that 2-

conductor VVF cables (vinyl-insulated vinyl

sheath cables) are used.

IRIS LEVEL Volume

751

The power to the camera body must be ON

termination

when adjustments are performed.

disconnected

 

Conductor diameter (mm)

ø1.0 mm

ø1.6 mm

ø2.0 mm

(AWG18)

(AWG14)

(AWG12)

 

Monitor TV

Maximum

DC 12 V

20 m

70 m

110 m

extension

 

(60 ft)

(220 ft)

(360 ft)

 

AC 24 V

70 m

180 m

280 m

 

 

(220 ft)

(590 ft)

(910 ft)

Cautions

If thin cables are used (i.e. with a high resistance), a significant voltage drop will occur when the unit is at its maximum power consumption. Either use a thick cable to restrict the voltage drop at the camera side to below 10%, or place the power supply near to the camera. If voltage drop occurs during operation, the performance will be unstable.

Do not allow input from both a DC 12 V and AC 24 V power supply at the same time.

When using a DC 12 V power supply, ensure that the polarities of the cable are correct.

The AC 24 V power supply should conform to the following:

For USA

: Class 2 only

For Europe

: Isolated power supply only

Note

Connecting multiple VN-C205 Cameras

In a system where more than 1 VN-C205 is used, turn on the power for a VN-C205 first, followed by setting the camera until "2-3 Setting IP Address for this Camera Using the 'VN-C205U Setup Tool' " is completed. Upon doing so, turn on a second camera and perform setting in the same way. Perform the same procedure for subsequent cameras.

Default IP address setting for all VN-C205 cameras is 198.168.0.2. When the power for multiple cameras are turned on at one time under a single LAN environment, therefore, proper access may not be established due to IP address redundancy. Do not turn on the power of more than 1 camera at the same time.

When IP address redundancy occurs, ensure that only one VN-C205 exists under a single LAN environment, and wait for some time (at least 10 minutes). In some cases, the power for all network devices under the same LAN environment may have to be turned off and on again to enable access to VN-C205.

22

Tilt lock screws

Horizontal

Lock screw

Variable range 120°

Vertical rotation

Focal length

adjustment ring IRIS LEVEL

FOCUS ADJ. switch

(  page 11)

Focus ring

Rotation levers

2.Adjusting the Lens and Camera Angle

Camera angle, zoom and focus are adjusted.

Horizontal rotation (adjustable range: 120°)

1 Loosen the horizontal LOCK screw.

2 Holding the both tilt lock screws, rotate horizontally.

3 Tighten the horizontal LOCK screw.

Vertical rotation

(adjustable range: +80°, –50°)

1 Loosen the tilt lock screws.

2 Holding the rotation levers, rotate vertically.

3 Tighten the tilt lock screws.

Image inclination (adjustable range: ±15°)

Manipulate the rotation levers to adjust the inclination of the image.

Adjusting the iris level

This adjustment only needs to be made when required.( page 10)

23

Page 12
Image 12
JVC VN-C205 manual Adjusting the iris level