Settings (Step 2 Network Settings)

2-4 Other Settings Using the "VN-C205U Setup Tool" (4. Alarm Setting) (Continued)

 Alarm Input

 

Item

 

Function/Set Value

Initial Value

1 Alarm 1/Alarm 2

This section describes setting procedures for alarm input.

 

Mode

For selecting whether to enable or disable the input signals.

Not Available

 

 

Set Values : Available, Not Available

 

 

Detect Mode

For selecting the method for detecting input signals.

Make

 

 

Make : Detect input signals at the "Make" contact point.

 

 

 

Break : Detect input signals during "Break".

 

 

 

Toggle : Detect input signals at both "Make" and "Break".

 

 

Alarm Output

For selecting whether to output from the alarm output terminal

Not Available

 

 

when there is alarm input.

 

 

 

Not Available : Do not output from the alarm output terminal.

 

 

 

Alarm Output 1 : Send output from the Alarm Output 1 terminal.

 

 

 

Alarm Output 2 : Send output from the Alarm Output 2 terminal.

 

 

 

Note

 

 

 

 

Unless the alarm output in the "Alarm Output" tab is enabled,

 

 

 

this function will not be activated even if alarm output is

 

 

 

selected in the alarm input settings. (Page 44)

 

 

 

 

 

 

Message Packet

For setting whether to send alarm packets to the PC when there

Not Available

 

 

is alarm input.

 

 

 

 

Not Available : Do not send alarm packets.

 

 

 

Available

: Send alarm packets.

 

 

Alarm FTP

For operation according to the [Alarm FTP] in the FTP Client

Not Available

 

 

feature when there is alarm input. Please refer to FTP Client

 

 

 

Settings (Page 50) for details on alarm FTP.

 

 

 

Set Values: Available, Not Available

 

 

Shutdown

Set to "Available" to quit all operations upon alarm input. Using

Not Available

 

 

this Shutdown function enables operations of this camera to

 

 

 

end safely even during recording into CF cards.

 

 

 

Not Available : Do not shut down.

 

 

 

Available

: Shut down.

 

Note

When this is set to "Available", all alarm input except alarm output and message packets will be disabled.

Item

Function/Set Value

Initial Value

2 Relay Alarm

Set here to enable the relay alarm function, which is activated

Not Available

 

when 2 alarms are received within a preset time interval.

 

 

The sequence and time interval for the alarm input can be specified.

 

 

When [Alarm Output] is selected, alarm signal output will be

 

 

sent to the alarm output terminal on the ceiling mount accord-

 

 

ing to the output port settings.

 

Notes

A second alarm input enables this relay alarm function, and alarm will not be activated for this second input.

Unless the alarm output in the "Alarm Output" tab is

enabled, this function will not be activated even if alarm output is selected in the alarm input settings. (Page 44)

Alarm Output * Please refer to the [Alarm 1/2] item for details on the set val- *Please

Message Packet

ues.

refer to

• Alarm FTP

 

the [Alarm

• Shutdown

 

1/2] item

 

 

for the

 

 

initial

 

 

values.

 

 

 

3 Retry (1 to 3)

For setting the no. of times alarm notification is to be sent to

1

 

the "V.Networks Controller". (Set Value: 1 to 3)

 

 

Note

 

 

• Alarm notification may fail, depending on the LAN

 

 

environment in use. If it fails, set the value for alarm

 

 

notification to "3". In this case, alarm by the "V.Networks

 

 

Controller" itself is set off only once.

 

 

 

 

4 List

Press here to display the IP address of the PCs to which an

 

alarm notification is sent. ("Distribution Address List" Screen)

 

 

To delete a distribution address, select the IP address to de-

 

 

lete, followed by pressing the Delete button.

 

Notes

The list allows setting of up to 10 addresses.

Message packets will not be sent out when there are 11 or more addresses.

42

 

 

 

43

Page 22
Image 22
JVC VN-C205 Alarm 1/Alarm, Detect Mode, Alarm Output, Message Packet, Available, Alarm FTP, Shutdown, Relay Alarm