Manuals / Konica Minolta / Computer Equipment / Network Card

Konica Minolta NC-6 user manual IPP Printing, Windows 2000/ Windows XP

Models: NC-6

1 50

Download 50 pages 42.42 Kb

Page 34

7.2.4IPP Printing

Connecting the Computer and Copier

7

7Enter the IP address for the copier into the Printer Name or IP Address box, and then click [Next>].

8Select Custom, and then click [Settings].

9Select RAW as the protocol.

10Enter “9100” for the Port Number setting, and then click [OK].

11Click [Next>].

12Click [Finish].

7.2.4IPP Printing

Windows 2000/ Windows XP

Important

Before continuing to set up the network settings, check the following:

Check that the computer is set up to use the TCP/IP protocol.

Check that the copier is also set up to use the TCP/IP protocol.

Check the IPP Settings Using PageScope Light

Use PageScope Light to access the copier and check if IPP printing is enabled. For instructions on using PageScope Light, refer to “8 Using PageScope Light”.

1Start up PageScope Light.

2Log in to the Administrator mode.

3Click the “Network” tab, and then select “IPP Configuration” in the menu.

4Check that Enable IPP is selected. If it is not selected, IPP printing is not possible.

NC-6

7-7

Image 34

Konica Minolta NC-6 user manual IPP Printing, Windows 2000/ Windows XP, Check the IPP Settings Using PageScope Light

Contents

User Manual Network Interface Card NC-64 Connecting the Network Cable ContentsChecking the Accessories 6 Printing the Configuration Page8 Using PageScope Light 9 AppendixFor Canada User InstructionsFor the U.S.A For EuropeFor countries not subject to Class B regulations For countries subject to Class B regulationsNC-6 1 Welcome 1.1 Trademark Acknowledgements 1.2 About PageScope Light2 Getting Ready 2.1 Selecting the Network Print Method For Windows 95 OSR 2.5/ Windows 98/ Windows 98 SE/ Windows MEFor Windows NT LPR TCP/IP protocol Windows NTFor Windows IPP PORT9100 TCP/IP protocol Windows XP IPX/SPX protocol NetWare serverTCP/IP protocol or NetWare client PC Windows computer2.2 Checking the Setup Procedures LPR / PORT 9100 Printing IPP Printing NetWare Server/Client except NDPS NetWare Server/Client NDPS3 Checking the Accessories 3.1 AccessoriesChecking the Accessories NC-64.2 Connecting the Network Cable 4 Connecting the Network Cable4.1 Types of Cable That Can Be Used Connecting the Network Cable NC-65 Assigning an IP Address 5.1 Entering the IP Address From the Control Panel5.2 Assigning an IP Address Check with your network administrator to determine if there is a DHCP server available on the network. If there is, a special IP address will be assigned by the AutoIP function. However, the copier will not be able to communicate with other devices on the network that have had ordinary IP addresses assigned to them. For details about the AutoIP function, refer to “Product Specifications” on page 9-1. Always select “SPECIFY” when there is no DHCP server available Assigning an IP Address 8 Use the 10-key pad and 6 Printing the Configuration Page Printing the Configuration Page NC-67 Connecting the Computer and Copier 7.1 Procedures Described in This Chapter7.2 Setting Up the Network Connections 7.2.1 Peer-to-Peer PrintingPage Connecting the Computer and Copier 10 Click Next 11 Click Finish NC-6Setting Up the LPR Connection Installing the Microsoft TCP/IP Printing ServiceWindows NT 7.2.3 Check the IPP Settings Using PageScope Light 7.2.4 IPP PrintingWindows 2000/ Windows XP Page 7.2.5 Connecting a Copier to the NetWare Server 7-10 Setting Up NetWare 4.x/ 5.x/ 6 Remote Printer ModeNC-6 Connecting the Computer and Copier Setting Up NetWare 5.x/ 6 Novell Distributed Print Service NDPS Creating an NDPS Printer AgentSetting Up the Windows Computer for the NetWare Client 7-14 Connecting the Computer and CopierNC-6 8.1 What is PageScope Light? 8 Using PageScope LightHTTP server Access Using PageScope Light 8.2 System Requirements 8.3 Accessing PageScope Light8.4 Using PageScope Light http//copierIPaddressNC-6 8.5 About the Screen LayoutThis is used to select various setting items or display Click on this to jump to the manufacturer’s Web siteThe default password for Administrator mode is “sysadm” 8.6 Logging In as an Administrator8.7 About the File Download Function Be sure to change the administrator password before usingUsing PageScope Light NC-69.1 Product Specifications 9 AppendixAppendix 9.2 TroubleshootingNC-6 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC Copyright 2003 KONICA MINOLTA BUSINESS TECHNOLOGIES, INCPrinted in China 4508-7782-01