Manuals / Konica Minolta / Computer Equipment / Network Card

Konica Minolta NC-6 user manual Connecting a Copier to the NetWare Server

Models: NC-6

1 50

Download 50 pages 42.42 Kb

Page 36

7.2.5Connecting a Copier to the NetWare Server

Connecting the Computer and Copier

7

7.2.5Connecting a Copier to the NetWare Server

Supported Environments

The controller supports the system environments described below.

NetWare version	Protocol	Emulation	Service mode
NetWare 4.x	IPX	NDS / Bindery	PServer / NPrinter

NetWare 5.x/6	IPX	NDS / Bindery	PServer / NPrinter

	TCP/IP		NDPS (lpr)

Setting Up NetWare 4.x/ 5.x/ 6 Print Server Mode

1Log in with administrator privileges.

2Start up NWadmin.

3Select the print service system or category container, and then select “Print service quick setup” from the Tool menu.

4Enter settings into the Print server name, Printer name, Print queue name, and Volume name boxes, select Other/Unknown under Type name, and then save the settings.

Note

Specify the users who can use the queue, printer options, number of queues, and password. Refer to the NetWare documentation for details.

5Start up PageScope Light and log in to the Administrator mode, select NetWare Configuration from the “Network” tab, and then use PageScope Light to specify the following settings on the copier. (Refer to “8 Using PageScope Light” for details.)

6Load MONITOR.NLM using the NetWare server console.

NC-6

7-9

Image 36

Konica Minolta NC-6 user manual Connecting a Copier to the NetWare Server

Contents

User Manual Network Interface Card NC-6Contents Checking the Accessories4 Connecting the Network Cable 6 Printing the Configuration Page8 Using PageScope Light 9 AppendixUser Instructions For the U.S.AFor Canada For EuropeFor countries subject to Class B regulations For countries not subject to Class B regulationsNC-6 1 Welcome 1.1 Trademark Acknowledgements 1.2 About PageScope Light2 Getting Ready 2.1 Selecting the Network Print Method For Windows 95 OSR 2.5/ Windows 98/ Windows 98 SE/ Windows MEFor Windows NT LPR TCP/IP protocol Windows NTFor Windows IPP PORT9100 TCP/IP protocol Windows XP NetWare server TCP/IP protocol orIPX/SPX protocol NetWare client PC Windows computer2.2 Checking the Setup Procedures LPR / PORT 9100 Printing IPP Printing NetWare Server/Client except NDPS NetWare Server/Client NDPS3 Checking the Accessories 3.1 AccessoriesChecking the Accessories NC-64 Connecting the Network Cable 4.2 Connecting the Network Cable4.1 Types of Cable That Can Be Used Connecting the Network Cable NC-65 Assigning an IP Address 5.1 Entering the IP Address From the Control Panel5.2 Assigning an IP Address Check with your network administrator to determine if there is a DHCP server available on the network. If there is, a special IP address will be assigned by the AutoIP function. However, the copier will not be able to communicate with other devices on the network that have had ordinary IP addresses assigned to them. For details about the AutoIP function, refer to “Product Specifications” on page 9-1. Always select “SPECIFY” when there is no DHCP server available Assigning an IP Address 8 Use the 10-key pad and 6 Printing the Configuration Page Printing the Configuration Page NC-67 Connecting the Computer and Copier 7.1 Procedures Described in This Chapter7.2 Setting Up the Network Connections 7.2.1 Peer-to-Peer PrintingPage Connecting the Computer and Copier 10 Click Next 11 Click Finish NC-6Installing the Microsoft TCP/IP Printing Service Setting Up the LPR ConnectionWindows NT 7.2.3 7.2.4 IPP Printing Check the IPP Settings Using PageScope LightWindows 2000/ Windows XP Page 7.2.5 Connecting a Copier to the NetWare Server Setting Up NetWare 4.x/ 5.x/ 6 Remote Printer Mode 7-10NC-6 Connecting the Computer and Copier Setting Up NetWare 5.x/ 6 Novell Distributed Print Service NDPS Creating an NDPS Printer AgentSetting Up the Windows Computer for the NetWare Client Connecting the Computer and Copier 7-14NC-6 8 Using PageScope Light 8.1 What is PageScope Light?HTTP server Access Using PageScope Light 8.3 Accessing PageScope Light 8.4 Using PageScope Light8.2 System Requirements http//copierIPaddress8.5 About the Screen Layout This is used to select various setting items or displayNC-6 Click on this to jump to the manufacturer’s Web site8.6 Logging In as an Administrator 8.7 About the File Download FunctionThe default password for Administrator mode is “sysadm” Be sure to change the administrator password before usingUsing PageScope Light NC-69.1 Product Specifications 9 Appendix9.2 Troubleshooting AppendixNC-6 Copyright 2003 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC Printed in ChinaKONICA MINOLTA BUSINESS TECHNOLOGIES, INC 4508-7782-01