Kramer Electronics VP-770 6.8.2.1 EAS Requirements

VP-770 - The OSD Menu

1. Set the dedicated EAS Ethernet connection port type and port number

through which the VP-770 will be listening, as a client, to intercept alerts.

By default, the dedicated EAS port settings are TCP, 5005. To change these

setting see the “Emergency Alert Configuration” in the table in Section 12.4.

2. Make sure that the VP-770 is connected to Ethernet.

3. Make sure that Alert System in the Miscellaneous menu is set to On (see

Section 6.8).

The VP-770 is now ready to receive any alert and display it.

6.8.2.1 EAS Requirements

The following table specifies the EAS requirements:

Text Length Definitions

Attribute Name

Max Size

Status

Certainty

Urgency

Severity

Event

Headline

Description

052

Instruction

052

Sender

Sent

Max 30 contiguous chars per word

Output Resolution

The output resolution needs to be at least 1280x768

Contents

Main USE R MAN UAL Page Page Page Page 1 Introduction 2 Getting Started ! 2.1 Achieving the Best Performance ! 2.2 Safety Instructions 2.3 Recycling Kramer Products 3 Overview Port tunneling, bidirectional RS-232 interface simple control commands Page Page 3.1 HDCP Compliance 3.2 About the Power Connect Feature 3.3 Using Twisted Pair Cable 3.4 Defining the VP-770 Presentation Switcher/Scaler Figure 1: VP-770 Presentation Switcher/Scaler Front Panel VP-770 Overview 8 Feature # VP-770 Overview 9 Function Feature # Page 4 Installing in a Rack 5 Connecting the VP-770 ! Page Page 5.1 Wiring the TP LINE IN / LINE OUT RJ-45 Connectors i This section defines the TP pinout, using a straight pin-to-pin cable with RJ-45 connectors. Note, that the cable Ground shielding must be connected / soldered to the connector shield. 5.2 Microphone Pinout 5.3 Audio Input Pinout 6 The OSD Menu 6.1 OSD Menu Operation Example Page Page 6.2 The Input Menu Page 6.2.1 Window Customization 23 6.2.1.1 Changing the Size of the Main and/or PiP Window Page Page Page 6.3 The Audio Menu Page 6.4 The Process Menu 6.5 The Picture Menu 6.6 The Enhance Menu 6.7 The Scale Menu 33 6.7.1 Selecting the Correct Aspect Ratio Page 6.8 The Miscellaneous Menu Page Page 6.8.2 The Emergency Alert System Page 6.8.2.1 EAS Requirements 41 7 The Display Modes 7.1 The Single Window Display Mode 7.1.1 Activating the Single window Mode 7.2 The Dual Window Display Mode Page 43 7.2.1 Activating the Dual Window Mode 7.2.2 Setting the OSD Menu to PiP Window Control Page 45 7.2.3.4 Selecting the PiP Source via the OSD Menu 8 Controlling the VP-770 8.1 Controlling via the Front Panel Buttons 8.1.1 Using the INPUT Front Panel buttons 47 8.2 Controlling via the OSD Menu 8.3 Controlling via the VP-770 Web Pages 8.3.1 Connecting to the VP-770 via your Browser 8.4 Connecting to the VP-770 via RS-232 8.5 Connecting the VP-770 via the ETHERNET Port 8.5.1 Connecting the ETHERNET Port directly to a PC (Crossover Cable) Page 8.5.3 Ethernet Port Configuration and Control ! 8.6 Controlling the VP-770 via the REMOTE Terminal Block Connector Page 8.7 Controlling via the Infrared Remote Control Transmitter 53 8.7.1 Using the IR Transmitter 9 Port Tunneling Page 10 Flash Memory Upgrade 11 Technical Specifications 11.1 Default Communication Parameters 11.2 Input Resolutions This section defines the input resolutions for each input 11.2.1 PC Input Resolutions 59 11.2.2 DP Input Resolutions 11.2.3 YUV Input Resolutions 11.2.4 CV Input Resolutions NTSC and PAL 11.3 Output Resolutions This section defines the output resolutions 11.3.1 HDMI Output Resolutions 11.3.2 PC Output Resolutions 12 The VP-770 RS-232 Communication Protocol 12.1 Using the Communication Protocol 12.2 Communication Protocol Mimicking OSD 12.2.1 Using the Communication Protocol with Protocol 3000 (the Y Command) 63 12.2.2 Using the Communication Protocol with Legacy Protocol 12.2.3 Protocol Table: Mimicking OSD table are therefore grayed out. The following table defines the protocol commands: VP-770 - The VP-770 RS-232 Communication Protocol 65 1st Level Func. Range Page Page Page Page Page VP-770 - The VP-770 RS-232 Communication Protocol 71 Response Syntax 12.3 Protocol Table: Mimicking Remote and Front Panel Buttons Keystroke Code 12.4 The Protocol 3000 Common Operation Commands Operation commands Command Lock front panel LOCK-FP LOCK-MODE Page #CR Page Page Page !