Manuals / Brands / Computer Equipment / Projector / Kramer Electronics / Computer Equipment / Projector

Kramer Electronics VP-770 11.1 Default Communication Parameters , 11.2 Input Resolutions

1 82

Download 82 pages, 3.74 Mb

58

VP-770 - Technical Specifications

11.1 Default Communication Parameters

RS-232

Protocol

3000 (Default)

Legacy

Baud Rate:

115,200

9,600

Data Bits:

8

8

Stop Bits:

1

1

Parity:

None

None

Command Format:

ASCII

ASCII

Example (Set display mode to Picture in Picture):

#Y 0,110,1<CR>

>Y 0 110 1<CR>

Ethernet

To reset the IP settings to the factory reset values, power cycle the device while holding in the

Ethernet Reset button, located on the rear panel of the unit

IP Address:

192.168.1.39

Subnet mask:

255.255.000.000

Default gateway:

000.000.000.000

TCP Port #:

5000

UDP Port #:

50000

Maximum UDP Ports:

10

Maximum TCP Ports:

4

Full Factory Reset

Front panel buttons

Turn power off. Turn power on again while holding the RESET TO

XGA/720p front panel button. The LEDs blink. Full factory reset is

complete once the LEDs cease to blink and react normally

OSD

Factory Reset through the Misc menu item

Protocol 3000

Use “Factory” command or #Y 0,760,1<CR>

11.2 Input Resolutions

This section defines the input resolutions for each input

11.2.1 PC Input Resolutions

PC Input Resolutions

640X480_60

800x600_75

625_P50

1280x1024_60

1400x1050_75

640x480_72

800x600_85

525_P60

1280x1024_75

1600x900_60

640x480_75

1024x768_60

720_P50

1280x1024_85

1600x1200_60

640x480_85

1024x768_70

720_P60

1360x768_60

1680x1050_60

800x600_56

1024x768_75

1280x800_60

1366x768_60

1920x1200_60RB

800x600_60

1024x768_85

1280x960_85

1440x900_60

1080_P50

800x600_72

1152x864_75

1280x768_60

1400x1050_60

1080_P60

Contents

Main USE R MAN UAL Page Page Page Page 1 Introduction 2 Getting Started ! 2.1 Achieving the Best Performance ! 2.2 Safety Instructions 2.3 Recycling Kramer Products 3 Overview Port tunneling, bidirectional RS-232 interface simple control commands Page Page 3.1 HDCP Compliance 3.2 About the Power Connect Feature 3.3 Using Twisted Pair Cable 3.4 Defining the VP-770 Presentation Switcher/Scaler Figure 1: VP-770 Presentation Switcher/Scaler Front Panel VP-770 Overview 8 Feature # VP-770 Overview 9 Function Feature # Page 4 Installing in a Rack 5 Connecting the VP-770 ! Page Page 5.1 Wiring the TP LINE IN / LINE OUT RJ-45 Connectors i This section defines the TP pinout, using a straight pin-to-pin cable with RJ-45 connectors. Note, that the cable Ground shielding must be connected / soldered to the connector shield. 5.2 Microphone Pinout 5.3 Audio Input Pinout 6 The OSD Menu 6.1 OSD Menu Operation Example Page Page 6.2 The Input Menu Page 6.2.1 Window Customization 23 6.2.1.1 Changing the Size of the Main and/or PiP Window Page Page Page 6.3 The Audio Menu Page 6.4 The Process Menu 6.5 The Picture Menu 6.6 The Enhance Menu 6.7 The Scale Menu 33 6.7.1 Selecting the Correct Aspect Ratio Page 6.8 The Miscellaneous Menu Page Page 6.8.2 The Emergency Alert System Page 6.8.2.1 EAS Requirements 41 7 The Display Modes 7.1 The Single Window Display Mode 7.1.1 Activating the Single window Mode 7.2 The Dual Window Display Mode Page 43 7.2.1 Activating the Dual Window Mode 7.2.2 Setting the OSD Menu to PiP Window Control Page 45 7.2.3.4 Selecting the PiP Source via the OSD Menu 8 Controlling the VP-770 8.1 Controlling via the Front Panel Buttons 8.1.1 Using the INPUT Front Panel buttons 47 8.2 Controlling via the OSD Menu 8.3 Controlling via the VP-770 Web Pages 8.3.1 Connecting to the VP-770 via your Browser 8.4 Connecting to the VP-770 via RS-232 8.5 Connecting the VP-770 via the ETHERNET Port 8.5.1 Connecting the ETHERNET Port directly to a PC (Crossover Cable) Page 8.5.3 Ethernet Port Configuration and Control ! 8.6 Controlling the VP-770 via the REMOTE Terminal Block Connector Page 8.7 Controlling via the Infrared Remote Control Transmitter 53 8.7.1 Using the IR Transmitter 9 Port Tunneling Page 10 Flash Memory Upgrade 11 Technical Specifications 11.1 Default Communication Parameters 11.2 Input Resolutions This section defines the input resolutions for each input 11.2.1 PC Input Resolutions 59 11.2.2 DP Input Resolutions 11.2.3 YUV Input Resolutions 11.2.4 CV Input Resolutions NTSC and PAL 11.3 Output Resolutions This section defines the output resolutions 11.3.1 HDMI Output Resolutions 11.3.2 PC Output Resolutions 12 The VP-770 RS-232 Communication Protocol 12.1 Using the Communication Protocol 12.2 Communication Protocol Mimicking OSD 12.2.1 Using the Communication Protocol with Protocol 3000 (the Y Command) 63 12.2.2 Using the Communication Protocol with Legacy Protocol 12.2.3 Protocol Table: Mimicking OSD table are therefore grayed out. The following table defines the protocol commands: VP-770 - The VP-770 RS-232 Communication Protocol 65 1st Level Func. Range Page Page Page Page Page VP-770 - The VP-770 RS-232 Communication Protocol 71 Response Syntax 12.3 Protocol Table: Mimicking Remote and Front Panel Buttons Keystroke Code 12.4 The Protocol 3000 Common Operation Commands Operation commands Command Lock front panel LOCK-FP LOCK-MODE Page #CR Page Page Page !