Serial Port Configuration, Snmp Configuration | Linksys EF1324

Instant EtherFast® Series

Serial Port Configuration

The Serial Port Configuration screen allows you to access the communication parameters for the Switch’s serial port. (Linksys recommends that you do not change the default settings.)

•Baud Rate - The rate at which data is sent between devices. Default is 19200. Options are 9600, 19200, and 38400 baud.

•Data Bits - Sets the data bits of the RS-232 port. Options are 7 and 8.

•Stop Bits - Sets the stop bits of the RS-232 port. Options are 1 and 2.

•Parity - Sets the parity of the RS-232 port. Default is None. Options are none, odd, and even.

•Time-Out- If no input is received from the attached device after this inter- val, the current session is automatically closed. Default is 10 minutes. The range is 0 to 100 minutes, where 0 indicates disabled.

•Auto Refresh - Sets the interval before a console session will auto refresh the console information, such as Spanning Tree Information, Port Configuration, Port Statistics, and RMON Statistics. Default is 1 second. The range is 0, or 5 to 255 seconds, where 0 indicates disabled.

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

EtherFast® Layer 3 Management 24-Port 10/100 + 2-Port Gigabit Ethernet Switch

SNMP Configuration

The SNMP Configuration screen displays parameters for the Simple Network Management Protocol (SNMP).

•Send Authentication Fail Traps - Issue a trap message to specified IP trap managers whenever authentication of an SNMP request fails. Default is enabled.

•SNMP Communities - Assigns SNMP access based on specified strings.

•IP Trap Managers - Specifies management stations that will receive authen- tication failure messages or other trap messages from the Switch.

Select OK to return to the previous panel.

22

23

Image 15

Linksys EF1324 manual Serial Port Configuration, Snmp Configuration

Contents

User Guide Copyright & Trademarks Table of Contents Introduction LEDs Getting to Know the Switch Gigabit Ports Installing the SwitchPre-Installation Considerations RJ-45 Ports Uplinking the Switch Switch ManagementRack-Mounting the Switch Powering on the Switch Web Management Telnet Management Connecting the Serial Cable to the Switch and Computer Main Menu Configuring the Switch Using the Console InterfaceLogging On to the Switch Overview System Information System Information Menu Management Setup Menu Switch Information IP Configuration Network Configuration IP Connectivity Test Ping Http Configuration Snmp Configuration Serial Port Configuration IP Trap Managers Snmp Communities Add User User Configuration Tftp Download Configuration File Device Control Menu Management Access Control System Mode Layer 2 Menu Port Configuration Port Trunking Configuration Mirror Port Configuration Static Unicast Address Configuration Add Static Address EntryApply Add Multicast Address Entry Static Multicast Address Configuration Bridge Menu Bridge Configuration Vlan Menu Spanning Tree Port Configuration Vlan and Priority Vlan Port Configuration IP Menu Vlan Table Configuration Modify Subnet Subnet Configuration Subnet Configuration Modify Ospf Configuration Subnet Configuration Modify RIP Configuration Subnet Configuration Modify Dvmrp Configuration Add Subnet Protocol Configuration RIP Configuration ARP Configuration Ospf Configuration Menu Ospf Area Configuration Add Ospf Area IP Menu Ospf Area Configuration Add Ospf Range Ospf Area Range Configuration Add Ospf Virtual Link Ospf Virtual Link Configuration Add Ospf Host Route Ospf Host Route Configuration Bootp Relay Database Configuration Add Bootp Relay ServerIgmp Snooping Configuration Add Static ARP Entry Static ARP Table Add Routing Entry Static Route Table Security Menu Default Route Menu MAC Filtering Configuration Security ModeAdd MAC Address Filter IP Security Filtering Configuration Igmp Snooping ConfigurationAdd IP Address Filter Port Statistics/Statistics Menu Network Monitor Menu Port Statistics InterfacesEthernet Rmon Statistics Layer 2 Address Table Spanning Tree Bridge Information Spanning Tree Port Information Vlan Dynamic Registration Information Vlan Information IP Multicast Registration Table Vlan Forwarding Information Subnet Information Routing Table ARP Table Igmp Cache Multicast Table Menu Multicast Forwarding Cache Dvmrp Neighbor Table Dvmrp Routing Table Ospf Interface Table Ospf Table Menu Ospf Neighbor Table Ospf Link State Table System Restart Menu Ospf Virtual Neighbor Table Troubleshooting Common Problems and SolutionsExit Your firmware has now been updated AppendixUpgrading Firmware via the Serial Port Glossary 121 123 Environmental Specifications Sales Information Warranty InformationTechnical Support RMA Issues Fax Contact Information T p / / w w w. l i n k s y s . c o m