Screen Capture, Restore Defaults | Lowrance electronic HDS-5X

Settings

Screen Capture

Saves images of your unit’s screen to your unit. You will only be able to review images on your unit. You can not save them to an MMC/SD card.

To take a screen capture:

1.Select Screen Capture from the System menu and press enter.

2.Press the LIGHT/Power key to capture the current screen. Repeat this step take additional screen captures.

NOTE: To view screenshots, go to the Pages menu, access

Utilities and select Files.

Restore Defaults

The Restore Defaults command switches the unit back to the settings it had when you purchased it (default). Instructions on Restoring defaults are covered in the

Getting Started section.

Advanced

A fine tuning adjustment for advanced users that allows you to turn on/off features and control settings like duplicate waypoint names and slider hold off.

Advanced Settings menu

Page 45

Image 45

Lowrance electronic HDS-5X operation manual Screen Capture, To take a screen capture, Restore Defaults, Advanced

Contents

HDS-5x Copyright 2011 Navico All Rights Reserved Table of contents Contents About this manual Manual Conventions Introduction Lowrance HDS-5x Sonar Getting Started Menus LanguageClosing Menus To select a language To select a fishing mode Selecting a Fishing ModeEntering Letters in Text Boxes To enter data in a text box To Restore Defaults Restore Defaults Pages Pages ScreenSelecting Pages Edit Mode To access Edit Overlay menuData Overlay Data Overlay menu To move/place a gauge Move or Placing a GaugeSelect Data Type Limits Size Add Source Configuration menuTo add a source To remove add source data On the Sonar Page you can Sonar Info Radar Page optionalOn the Radar Page you can On the Info Page you can Info menu DashboardsEdit To edit gauge display Edit Info menuTo select info To Configure Limits To add sourceTo remove a source To change layout Change LayoutAdd Dashboard To add a dashboard To access Utilities SettingsUtilities Utilities Displaying Combo Pages Selecting an Active PanelTo display a combo Displaying Multiple Panels Adjust Panel SizesTo display multiple panels Left the Info page on the right To adjust panel sizes Sonar Operation To access the Sonar Sonar Menu Auto SensitivitySensitivity Range ColorlineFrequency Split Adjust To Adjust Sensitivity and ColorlineStop Sonar Sonar Options To set Upper and Lower LimitsCustom Upper and Lower Limits Ping Speed Palette To select a Split optionTo select a Palette Depth Line Temperature GraphAmplitude Scope Zoom Bars Fish ID Measure DistanceTo select a Fish ID option To Measure distance To share/receive sonar data Radar Operation optional To access the Radar To access the Adjust menu Adjust menuRadar menu Radar State Auto Gain Low, Medium and HighTo select Auto Gain Acquire Targets Sea ClutterPosition To change the PPI position Look Ahead Symbology To adjust an EBL/VRM AdjustEBL/VRM menu To select an EBL/VRM Data Box Guard Zones To choose alarm trigger vessels entering or exiting zones Using the Adjust menuTo turn on a Guard Zone To change the shape of Guard Zones To access the System menu Settings MenuSystem Language To change Text Size To change Key Beep settingsKey Beeps Time optional Screen Capture Restore DefaultsTo take a screen capture Advanced To adjust cursor settings To access Advanced SettingsPages About Network Sonar Sonar SettingsNoise Rejection Surface Clarity Manual Mode To adjust Surface ClarityScroll Speed Fishing Modes Installation Menu Reset Fishing ModeKeel Offset Water Speed Calibration To set Keel OffsetTo calibrate Water Speed Temperature Averaging Temperature CalibrationWater Speed Averaging To select a Water Averaging interval To select a Temperature Averaging interval Transducer TypeTo select a Transducer Type Target Expansion Radar Settings Menu optionalTarget Trails Palette Orientation North IndicatorThreshold To change Map Orientation Range Markers Range RingsCompass Bearings To set T/M or R Marpa To adjust CPA and Tcpa settings Canceling Marpa targetsSelecting Marpa targets To cancel all targets To cancel individual targetsMarpa Settings To select history length Target Alarms InstallationTo set Marpa target alarm To access Radar Installation menu Installation Adjustment Menu Bearing alignmentTo select Heading up orientation To Adjust Bearing Alignment To Adjust Range OffsetRange offset To Adjust Antenna Height Fast scan mode BR24 Radar onlyAntenna Height Tune Reset Radar to Factory Defaults Manually adjusting Sidelobe suppressionSidelobe suppression BR24 only Fuel RefuelTo input fuel added To calibrate engines To set tank to full Fuel Used Vessel Setup To select engine-tank configuration Engine/Tank ConfigurationTo input tank size Calibrate To enable/disable an Alarm Alarms Units Siren Enabled To auto configure a network Auto ConfigureNetwork Data Sources Rename Data Source menuTo Rename a data source New To reset global or local sources Reset Global and Reset LocalTo select a scope Device List To configure a device name or device tank size Configuring Devices To access calibration instructions To configure device locationInstance Calibrating devices Nmea 2000 receive/send waypoint DiagnosticsTo view waypoints Serial Ports To configure serial ports To access Nmea 0183 Output screenNmea 0183 Output Demo Mode To adjust CPA or Tcpa settingsTo choose a Demo Mode Simulator General Specifications HDS-5x Unit Care Cleaning the screen Unit won’t turn on TroubleshootingUnit freezes, locks up, or operates erratically Weak bottom echo, erratic readings or no fish returns Troubleshooting No fish arches when Fish I.D. is turned off Noise Update the Software Reset the UnitRadar won’t Start Up Troubleshooting Index Index Marpa Index

Lowrance electronic HDS-5X Screen Capture, To take a screen capture, Restore Defaults, Advanced

Models: HDS-5X

Screen Capture

To take a screen capture:

Restore Defaults

Advanced