| Table | ||
|
|
| |
Field | Default | Description | |
Value | |||
|
| ||
|
|
| |
PS | 0 | Parameters Savable. This bit is only used with the MODE SENSE command. A returned val- | |
ue of 1 indicates that the target is capable of saving the page in a | |||
|
| location. The bit is reserved with the MODE SELECT command. | |
EER | 0 | Enable Early Recovery. Not supported by the drive. | |
|
|
| |
|
| Post Error Recovery. When the value is 1, the drive returns CHECK CONDITION status for | |
|
| recovered errors, sets the sense key to RECOVERED ERROR, and posts the appropriate ad- | |
PER | 0 | ditional sense code. | |
When set to the default value of 0, it causes the drive to return GOOD status in cases where | |||
|
| ||
|
| error recovery is invoked and is successful. The only recoverable error that can occur during | |
|
| a VERIFY operation is a failed read that succeeds after retries. | |
DTE | 0 | Disable Transfer on Error. Not supported by the drive. | |
|
|
| |
DCR | 0 | Disable Correction. When the value is 1, it disables ECC Firmware only (but not retries) on | |
the READ portion of a VERIFY operation. When set to the default value of 0, the ECC cor- | |||
|
| rection is always applied as a means of recovering erred data. | |
Verify | 4 | The Verify Retry Count specifies the number of retries that are attempted per sector on a | |
Retry Count | failed READ portion of a VERIFY operation. | ||
| |||
Verify |
| The Verify Correction Span specifies the maximum number of bits in a sector that the drive | |
240 | is allowed to correct. A value less than the default value can cause an otherwise correctable | ||
Correction | error to be reported as uncorrectable. If the initiator specifies a value larger than 80, the drive | ||
Span |
| rounds down to 80 without reporting the change. A value of 0 causes the drive to use its de- | |
|
| fault value. The drive ignores any value in this field. | |
Verify | 0 | The Verify Recovery Time Limit specifies (in milliseconds) the maximum time that a retry | |
Recovery | is attempted on a failed sector during the read portion of a verify operation. The default value | ||
Time Limit |
| of 0 indicates that there is no time limit. The minimum permissible is 100 milliseconds. |
5.12.9Caching Page (08h)
The Caching Page controls the drive’s cache management policy. The data format and field descriptions are described in Table
Table
Byte |
| Bit | 7 | 6 | 5 |
| 4 | 3 |
| 2 | 1 | 0 |
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
| |
| 0 |
| PS | Rsvd |
|
|
| Page Code (08h) |
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||
| 1 |
|
|
|
|
| Page Length (12h) |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 |
| IC | ABPF | CAP |
| DISC | Size |
| WCE | MF | RCD |
|
|
|
|
|
|
|
|
|
|
| ||
| 3 |
| Demand Read Retention Priority | Demand Write Retention Priority | ||||||||
|
|
|
|
|
|
|
|
| ||||
4 | – 5 |
|
|
| Disable | Transfer Length |
|
| ||||
|
|
|
|
|
|
|
|
|
|
| ||
6 | – 7 |
|
|
|
|
| Minimum |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||
8 | – 9 |
|
|
|
|
| Maximum |
|
|
| ||
|
|
|
|
|
|
|
|
|
| |||
10 | – 11 |
|
|
|
| Maximum |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| 12 |
| FSW | LBCSS | DRA |
| VS | VS |
|
| Reserved |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 13 |
|
|
|
|
| Number of Cache Segments |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||
14 | – 15 |
|
|
|
|
| Cache Segment Size |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||
| 16 |
|
|
|
|
| Reserved |
|
|
| ||
|
|
|
|
|
|
|
|
|
| |||
17 | – 19 |
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|