Sense | Sense | Sense | Meaning | |
Key | Code | Qualifier | ||
| ||||
|
|
|
| |
0x04 | 0x40 | 0x80 | Unknown HW problem | |
Hdwe Error |
|
|
| |
0x40 | 0x82 | Hardware Bug Check (check Info field) | ||
| ||||
|
|
|
| |
| 0x40 | 0x83 | Failed HDA test. | |
|
|
|
| |
| 0x40 | 0x84 | Failed PCB test. | |
|
|
|
| |
| 0x40 | 0x85 | EDC check failed. | |
|
|
|
| |
| 0x40 | 0x86 | Controller FIFO over/underflow error. | |
|
|
|
| |
| 0x40 | 0x88 | DIAG: Drive failed to read servowriter serial number. | |
|
|
|
| |
| 0x40 | 0x89 | DIAG: Failed XOR test. | |
|
|
|
| |
| 0x40 | 0x90 | EDC Check Failed 0 | |
|
|
|
| |
| 0x40 | 0x91 | EDC Check Failed 1 | |
|
|
|
| |
| 0x40 | 0x92 | EDC Check Failed 2 | |
|
|
|
| |
| 0x40 | 0x93 | EDC Check Failed3 | |
|
|
|
| |
| 0x40 | 0x8A | Servo restart failed after set RPM command | |
|
|
|
| |
| 0x40 | 0x8C | LBA mismatch error | |
|
|
|
| |
| 0x40 | 0x8D | ETM test failure, drive failed to spin | |
|
|
|
| |
| 0x40 | 0x8E | Could not achieve target RPM | |
|
|
|
| |
| 0x40 | 0xA0 | Test did not complete | |
|
|
|
| |
| 0x40 | 0xA1 | Test completed successfully, but failed. | |
|
|
|
| |
| 0x40 | 0xA2 | Invalid parameter was received. | |
|
|
|
| |
| 0x40 | 0xA3 | Invalid data in servo record. Prevented algorithm from completing. | |
|
|
|
| |
| 0x40 | 0xA4 | Servo record did not complete | |
|
|
|
| |
| 0x40 | 0xA5 | Read seek failed | |
|
|
|
| |
| 0x40 | 0xA6 | Write seek failed | |
|
|
|
| |
| 0x40 | 0xA7 | Raw seek failed | |
|
|
|
| |
| 0x40 | 0xA8 | Servo Diagnostic Test running. | |
|
|
|
| |
| 0x40 | 0xA9 | Invalid 97/98 super cmd seq. Must send 97 before 98 | |
|
|
|
| |
| 0x40 | 0xAA | Super Command 97 already running | |
|
|
|
| |
| 0x40 | 0xAB | Complex magnitude is zero | |
|
|
|
| |
| 0x40 | 0xAC | Could not complete the | |
|
|
|
| |
| 0x40 | 0xAD | Got a divide by zero error in complex divide. | |
|
|
|
| |
| 0x40 | 0xAE | WGATE negated due to shock or bump during BCV write | |
|
|
|
| |
| 0x40 | 0xAF | Servo Death occurred during a BVC write operation | |
|
|
|
| |
| 0x40 | 0xB0 | Seek command completion timeout occurred | |
|
|
|
| |
| 0x40 | 0xB1 | Read an impossibility high number of good BCVS on this | |
|
|
|
| |
| 0x40 | 0xB2 | No read passes resulted in enough test BCVs being read | |
|
|
|
| |
| 0x40 | 0xB3 | The last read pass for test BCVs was good but shouldn’t be | |
|
|
|
| |
| 0x40 | 0xB4 | DestinationLoc expected vs actual mismatch. servo death recovery | |
|
|
|
| |
| 0x44 | 0x00 | Logical assertion (firmware consistency check) | |
|
|
|
| |
| 0x44 | 0x84 | Insufficient buffer memory for operation | |
|
|
|
| |
| 0x90 | 0x01 | Serial Port Packet Receive Error | |
|
|
|
|