![](/images/backgrounds/146247/146247-253100x1.png)
5.12.7Disconnect–Reconnect Page (02h)
The
Table
Byte | Bit | 7 | 6 |
| 5 |
| 4 |
| 3 | 2 | 1 | 0 | |
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 |
| PS | Rsvd |
|
|
|
|
| Page Code (02h) |
|
| |
|
|
|
|
|
|
|
|
|
|
| |||
| 1 |
|
|
|
|
| Page Length (0Eh) |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||
| 2 |
|
|
|
|
| Buffer Full Ratio |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||
| 3 |
|
|
|
|
| Buffer Empty Ratio |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||
4 | – | 5 |
|
|
|
| Bus Inactivity Limit |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||
6 | – | 7 |
|
|
|
| Disconnect Time Limit |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||
8 | – | 9 |
|
|
|
| Connect Time Limit |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||
10 | – | 11 |
|
|
|
| Maximum Burst Size |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 12 |
| EMDP |
| Fairness Arbitration |
|
| DImm |
| DTDC |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 13 |
|
|
|
|
|
|
| Reserved |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
14 | – | 15 |
|
|
|
|
| First Burst Size |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Table | ||
|
|
| |
Field | Default | Description | |
Value | |||
|
| ||
|
|
| |
|
| Parameters Savable. This bit is only used with the MODE SENSE command. A re- | |
PS | 0 | turned value of 1 indicates that the target is capable of saving the page in a non- | |
volatile, | |||
|
| ||
|
| command. | |
|
|
| |
Buffer Full |
| The Buffer Full Ratio indicates how full the buffer should be prior to requesting an | |
0 | interconnect tenancy. Applies to READ operations only. The default of 0 indicates | ||
Ratio | |||
| to the drive that it should use its default ratio. | ||
|
| ||
|
|
| |
Buffer Empty |
| The Buffer Empty Ratio indicates how full the buffer should be prior to requesting | |
0 | an interconnect tenancy. Applies to READ operations only. The default of 0 indi- | ||
Ratio | |||
| cates to the drive that it should use its default ratio. Not supported by the drive. | ||
|
| ||
|
|
| |
Bus Inactivity | 0 | The Bus Inactivity Limit indicates the maximum duration of any interconnect ten- | |
Limit | ancy during which no data is transferred. Not supported by the drive. | ||
| |||
|
| The Disconnect Time Limit specifies the minimum time, in 100 microsecond in- | |
Disconnect |
| crements, that the drive waits after releasing the SCSI bus before reselecting. The | |
0 | drive supports a maximum value of 0xFF. Values greater than 0xFF are treated as | ||
Time Limit | |||
| 0xFF. The default value of 0 indicates that the drive can reslect immediately after | ||
|
| ||
|
| releasing the bus. | |
|
|
| |
Connect Time | 0 | The Connect Time Limit indicates the maximum duration of a single interconnect | |
Limit | tenancy. Not supported by the drive. | ||
| |||
|
| The Maximum Burst Size | |
|
| specifies the maximum amount of data that the drive will transfer during a data | |
Maximum Burst |
| phase before disconnecting from the bus, assuming it was given the disconnect | |
0 | privilege. This value is expressed in increments of data sectors (that is, a value of | ||
Size | |||
| 1 indicates 512 bytes, a value of 2 indicates 1024 bytes). The default value of 0 in- | ||
|
| ||
|
| dicates that there is no limit on the amount of data transferred per connection. This | |
|
| field is reserved for the |