CLI Management

The system supports two types of console management – CLI command and Menu selection. After you login to the system, you will see a command prompt. To enter CLI management interface, enter “enable” command. The following table lists the CLI commands and description.

Commands Level

 

Modes

 

Access Method

 

Prompt

 

Exit Method

 

About This Mode1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The user commands available at

 

 

 

 

 

 

 

 

 

the user level are a subset of

 

 

 

Begin a session with

 

 

 

Enter logout or

 

those available at the privileged

 

User EXEC

 

 

switch>

 

 

level.

 

 

your switch.

 

 

quit.

 

 

 

 

 

 

 

 

Use this mode to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Perform basic tests.

 

 

 

 

 

 

 

 

 

• Display system information.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The privileged command is

 

Privileged

 

Enter the enable

 

 

 

Enter disable to

 

advance mode

 

 

command while in

 

switch#

 

 

Privileged this mode to

 

EXEC

 

 

 

exit.

 

 

 

user EXEC mode.

 

 

 

 

• Display advance function status

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Save configures

 

 

 

 

 

 

 

 

 

 

 

 

 

Enter the configure

 

 

 

To exit to

 

Use this mode to configure

 

 

 

command while in

 

 

 

privileged EXEC

 

 

Global Configuration

 

 

switch (config)#

 

 

parameters that apply to your

 

 

privileged EXEC

 

 

mode, enter exit

 

 

 

 

 

 

 

 

switch as a whole.

 

 

 

mode.

 

 

 

or end

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Enter the vlan

 

 

 

To exit to user

 

 

 

 

 

database command

 

 

 

 

Use this mode to configure

 

VLAN database

 

 

switch (vlan)#

 

EXEC mode,

 

 

 

while in privileged

 

 

 

VLAN-specific parameters.

 

 

 

 

 

 

enter exit.

 

 

 

 

EXEC mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Enter the interface

 

 

 

To exit to global

 

Use this mode to configure

 

Interface

 

command (with a

 

switch

 

configuration

 

 

 

 

 

 

parameters for the switch and

 

configuration

 

specific interface)

 

(config-if)#

 

mode, enter exit.

 

 

 

 

 

 

Ethernet ports.

 

 

 

while in global

 

 

 

To exist to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13

 

 

 

 

Page 21
Image 21
Milan Technology MIL-SM8002TG manual CLI Management, Commands Level