Email Alarm Events Settings | Moxa Technologies EDS-508 guide

EDS-508 Series User’s Manual

Featured Functions

2.Configuring Email Settings

To configure EDS’s email setup from the Console interface or browser interface, enter your Mail Server IP/Name (IP address or name), Account Name, Account Password, Retype New Password, and the email address(es) to which warning messages will be sent.

3.Activate your settings and test email if necessary

After configuring and activating your MOXA EtherDevice Switch’s Event Types and Email Setup, you can use the Test Email function to see if your e-mail addresses and mail server address have been properly configured.

Email Alarm Events Settings

Event Types

Event Types can be divided into two basic groups: System Events and Port Events. System Events are related to the overall function of the Switch, whereas Port Events are related to the activity of a specific port.

System Event	Warning e-mail is sent when…
Switch Cold Start	Power is cut off and then reconnected.

Switch Warm Start	EDS is rebooted, such as when network parameters
	are changed (IP address, netmask, etc.).
Power Transition (On"Off)	EDS is powered down.
Power Transition (Off"On)	EDS is powered up.
DI1 (On"Off)	Digital Input 1 is triggered by on to off transition
DI1 (Off"On)	Digital Input 1 is triggered by off to on transition

DI2 (On"Off)	Digital Input 2 is triggered by on to off transition

DI2 (Off"On)	Digital Input 2 is triggered by off to on transition

Configuration Change Activated	Any configuration item is changed.

Comm. Redundancy Topology	If any Spanning Tree Protocol switches have
Changed	changed their position (applies only to the root of the
	tree).
	If Master of Turbo Ring has changed or backup path
	is activated.
Authentication Failure	An incorrect password is entered.
	3-48

Image 64

Moxa Technologies EDS-508 user manual Email Alarm Events Settings, Event Types, Configuring Email Settings, System Event

Contents

Moxa EtherDevice Switch User’s Manual EDS-508 Series Second Edition, November Moxa EtherDevice Switch EDS User’s Manual Copyright NoticeTrademarks Disclaimer Table of Contents Chapter EDS Configurator GUI Introduction Moxa EtherDevice Switch Package ChecklistInside the Future of Industrial Ethernet Technology Industrial vs. Commercial Features Useful Utility and Remote ConfigurationAdvanced Industrial Networking Capability Designed for Industrial ApplicationsPage Getting Started Using the RS-232 Serial Console 115200, None, 8, 1, VT100 Connection Caution EDS-508 Series User’s Manual Getting Started Using the Telnet Console Key Function EDS-508 Series User’s Manual Getting Started Using Web Configuration For details Page Featured Functions Configuring Basic Settings Switch Name Setting Descriptions Factory DefaultSwitch Location Setting Descriptions Factory Default Switch Description Setting Descriptions Factory Default Password Disable Telnet/Web ConsoleSetting Descriptions Factory Default Account Name Accessible IP Password Setting# Hosts on the specific subnet can access the NE-4000T # Any host can access the NE-4000T Port Enable/Disable PortName Port Type Port Transmission SpeedFDX Flow Control Auto IP Configuration Switch IP AddressSwitch Subnet Mask Default Gateway Time Current Time Setting Description Factory DefaultDNS IP Address Time Zone Setting Description Factory Default Current Date Setting Description Factory DefaultSystem Up Time Tftp Server IP/Name Setting Description Factory Default System File Update-By Remote TftpLog file path and name Setting Description Factory Default System File Update-By Local Import/Export Configuration File ExportConfiguration File Import Log File Export Factory Default Using Port TrunkingConcept of Port Trunking Port Trunking Settings Configuring Port TrunkingTrunking settings Port setting information Using SnmpEnable/Disable Configuring Snmp Snmp Read/Write Settings Snmp VersionsV1, V2c Read Community V1, V2c Read/Write Community Admin Auth. Type For Snmp V1, V2c, V3 and V3 only Admin Data Encryption Key For Snmp V1, V2c, V3 and V3 onlyUser Auth. Type For Snmp V1, V2c, V3 and V3 only User Data Encryption Key For Snmp V1, V2c, V3 and V3 only Using Communication Redundancy Trap SettingsPrivate MIB information Concept of Turbo Ring When the number of EDS units in the Turbo Ring is even Page Switch a Coupler Configuring Turbo Ring Concept of STP/RSTP What is STP? How STP Works STP Requirements STP Configuration STP ReconfigurationHow Rstp Differs from STP Port Speed Path Cost 802.1D Edition 802.1w-2001 Using STP on a Network with Multiple VLANs STP Example Configuring STP/RSTP Root/Not Root Protocol of RedundancyBridge priority Hello time sec Enable STP per Port Configuration Limits of RSTP/STPMax. Age sec Port Priority Using Traffic Prioritization What is Traffic Prioritization?Concept of Traffic Prioritization How Traffic Prioritization Works Ieee 802.1p Priority Level Ieee 802.1D Traffic Type Differentiated Services DiffServ Traffic MarkingTraffic Prioritization QoS Classification Configuring Traffic PrioritizationTraffic Queues Default Port Priority Queuing MechanismInspect TOS Inspect COS CoS Mapping TOS/DiffServ Mapping Using Virtual LAN What is a VLAN?Concept of Virtual LAN Vlan Benefits of VLANs VLANs and Moxa EtherDevice Switch Management VlanCommunication Between VLANs VLANs Tagged and Untagged Membership Sample Applications of VLANs using Moxa EtherDevice Switch Device a Switch a Switch B Configuring 802.1Q Vlan Vlan Port Settings Management Vlan Setting Port PvidPort Fixed Vlan List Tagged Port Forbidden Vlan List Using Multicast Filtering What is an IP Multicast?Concept of Multicast Filtering Vlan Table Multicast Filtering Network without multicast filtering Configuring Multicast Filtering Multicast Filtering and Moxa EtherDevice SwitchIgmp Multicast Filtering Enabling Igmp Snooping Igmp Snooping Settings Querier interval Igmp Snooping Enable GlobalIgmp Snooping Enable per Vlan Static Multicast Router Port Using Rate Limiting Add Static Multicast MACIgmp Table Add New Static Multicast Address to the List Configuring Rate Limiting Ingress PolicyRate of Low Priority Queue Rate of Normal Priority Queue Using Port Lock Adding a Static Unicast MAC AddressRate of Medium Priority Queue Rate of High Priority Queue Using Auto Warning Configuring Port LockConfiguring Email Warning Add Static Unicast MAC Address Email Alarm Events Settings Configuring Email SettingsActivate your settings and test email if necessary Event Types MoxaEtherDeviceSwitch0001@SwitchLocation Email SettingsPort Event Configuring Relay Warning Configuring Relay Event TypesMail Server IP/Name Email Address Relay Alarm Events Settings Activate your settings Relay Alarm List Using Line-Swap-Fast-RecoveryOverride relay alarm settings Configuring Line-Swap Fast Recovery Using Set Device IPEnable Line-Swap-Fast-Recovery Configuring Set Device IP Set up the connected devices Using Diagnosis Mirror PortDesired IP Address Output data stream Monitor by Switch Using MonitorPing Monitor by Port Using the MAC Address Table ALL Using Event Log Page EDS Configurator GUI Starting EDS Configurator Broadcast Search Search by IP address Upgrade Firmware Modify IP Address Export Configuration Import Configuration Unlock Server LockedUnlocked Blank Locked Fixed FixedUnlocked Fixed MIB Groups Page Specifications TechnologyInterface Optical Fiber Power MechanicalEnvironment Regulatory Approvals Service Information Moxa Internet Services Following services are provided Moxa Product % EDS-508 Problem Report FormSerial Number Product Return Procedure