Configuring Set Device IP | Moxa Technologies EDS-508 manual

EDS-508 Series User’s Manual

Featured Functions

STEP 1—set up the connected devices

Set up the Ethernet-enabled devices connected to MOXA EtherDevice Switch for which you would like the IP addresses to be assigned automatically. The devices must be configured to obtain their IP address automatically.

The devices’ configuration utility should include a setup page that allows you to choose an option similar to Obtain an IP address automatically.

For example, Windows’ TCP/IP Properties window is shown at the right. Although your device’s configuration utility may look quite a bit different, this figure should give you some idea of what to look for.

You also need to decide which of MOXA EtherDevice Switch’s ports your Ethernet-enabled devices will be connected to. You will need to set up each of these ports separately, as described in the following step.

STEP 2

Configure MOXA EtherDevice Switch’s Set device IP function, either from the Console utility or from the Web Browser interface. In either case, you simply need to enter the Desired IP for each port that needs to be configured.

STEP 3

Be sure to activate your settings before exiting.

•When using the Web Browser interface, activate by clicking on the Activate button.

•When using the Console utility, activate by first highlighting the Activate menu option, and then press Enter. You should receive the Set device IP settings are now active! (Press any key to continue) message.

Configuring Set Device IP

3-54

Image 70

Moxa Technologies EDS-508 user manual Configuring Set Device IP, Set up the connected devices

Contents

Moxa EtherDevice Switch User’s Manual EDS-508 Series Second Edition, November Trademarks Moxa EtherDevice Switch EDS User’s ManualCopyright Notice Disclaimer Table of Contents Chapter EDS Configurator GUI Introduction Inside the Future of Industrial Ethernet Technology Moxa EtherDevice SwitchPackage Checklist Industrial vs. Commercial Advanced Industrial Networking Capability FeaturesUseful Utility and Remote Configuration Designed for Industrial ApplicationsPage Getting Started Using the RS-232 Serial Console 115200, None, 8, 1, VT100 Connection Caution EDS-508 Series User’s Manual Getting Started Using the Telnet Console Key Function EDS-508 Series User’s Manual Getting Started Using Web Configuration For details Page Featured Functions Switch Location Setting Descriptions Factory Default Configuring Basic SettingsSwitch Name Setting Descriptions Factory Default Switch Description Setting Descriptions Factory Default Setting Descriptions Factory Default PasswordDisable Telnet/Web Console Account Name # Hosts on the specific subnet can access the NE-4000T Accessible IPPassword Setting # Any host can access the NE-4000T Port Enable/Disable PortName Port Type Port Transmission SpeedFDX Flow Control Switch Subnet Mask Auto IP ConfigurationSwitch IP Address Default Gateway Time Current Time Setting Description Factory DefaultDNS IP Address Time Zone Setting Description Factory Default Current Date Setting Description Factory DefaultSystem Up Time Tftp Server IP/Name Setting Description Factory Default System File Update-By Remote TftpLog file path and name Setting Description Factory Default Configuration File Import System File Update-By Local Import/ExportConfiguration File Export Log File Export Factory Default Using Port TrunkingConcept of Port Trunking Port Trunking Settings Configuring Port TrunkingTrunking settings Port setting information Using SnmpEnable/Disable V1, V2c Read Community Configuring Snmp Snmp Read/Write SettingsSnmp Versions V1, V2c Read/Write Community User Auth. Type For Snmp V1, V2c, V3 and V3 only Admin Auth. Type For Snmp V1, V2c, V3 and V3 onlyAdmin Data Encryption Key For Snmp V1, V2c, V3 and V3 only User Data Encryption Key For Snmp V1, V2c, V3 and V3 only Private MIB information Using Communication RedundancyTrap Settings Concept of Turbo Ring When the number of EDS units in the Turbo Ring is even Page Switch a Coupler Configuring Turbo Ring Concept of STP/RSTP What is STP? How STP Works STP Requirements How Rstp Differs from STP STP ConfigurationSTP Reconfiguration Port Speed Path Cost 802.1D Edition 802.1w-2001 Using STP on a Network with Multiple VLANs STP Example Configuring STP/RSTP Bridge priority Root/Not RootProtocol of Redundancy Hello time sec Max. Age sec Enable STP per PortConfiguration Limits of RSTP/STP Port Priority Concept of Traffic Prioritization Using Traffic PrioritizationWhat is Traffic Prioritization? How Traffic Prioritization Works Ieee 802.1p Priority Level Ieee 802.1D Traffic Type Differentiated Services DiffServ Traffic MarkingTraffic Prioritization QoS Classification Configuring Traffic PrioritizationTraffic Queues Inspect TOS Default Port PriorityQueuing Mechanism Inspect COS CoS Mapping TOS/DiffServ Mapping Concept of Virtual LAN Vlan Using Virtual LANWhat is a VLAN? Benefits of VLANs Communication Between VLANs VLANs and Moxa EtherDevice SwitchManagement Vlan VLANs Tagged and Untagged Membership Sample Applications of VLANs using Moxa EtherDevice Switch Device a Switch a Switch B Configuring 802.1Q Vlan Vlan Port Settings Port Fixed Vlan List Tagged Management Vlan SettingPort Pvid Port Forbidden Vlan List Concept of Multicast Filtering Using Multicast FilteringWhat is an IP Multicast? Vlan Table Multicast Filtering Network without multicast filtering Igmp Multicast Filtering Configuring Multicast FilteringMulticast Filtering and Moxa EtherDevice Switch Enabling Igmp Snooping Igmp Snooping Enable per Vlan Igmp Snooping Settings Querier intervalIgmp Snooping Enable Global Static Multicast Router Port Igmp Table Using Rate LimitingAdd Static Multicast MAC Add New Static Multicast Address to the List Rate of Low Priority Queue Configuring Rate LimitingIngress Policy Rate of Normal Priority Queue Rate of Medium Priority Queue Using Port LockAdding a Static Unicast MAC Address Rate of High Priority Queue Configuring Email Warning Using Auto WarningConfiguring Port Lock Add Static Unicast MAC Address Activate your settings and test email if necessary Email Alarm Events SettingsConfiguring Email Settings Event Types MoxaEtherDeviceSwitch0001@SwitchLocation Email SettingsPort Event Mail Server IP/Name Configuring Relay WarningConfiguring Relay Event Types Email Address Relay Alarm Events Settings Activate your settings Relay Alarm List Using Line-Swap-Fast-RecoveryOverride relay alarm settings Configuring Line-Swap Fast Recovery Using Set Device IPEnable Line-Swap-Fast-Recovery Configuring Set Device IP Set up the connected devices Desired IP Address Using DiagnosisMirror Port Output data stream Monitor by Switch Using MonitorPing Monitor by Port Using the MAC Address Table ALL Using Event Log Page EDS Configurator GUI Starting EDS Configurator Broadcast Search Search by IP address Upgrade Firmware Modify IP Address Export Configuration Import Configuration Unlocked Unlock ServerLocked Blank Locked Fixed FixedUnlocked Fixed MIB Groups Page Interface SpecificationsTechnology Optical Fiber Environment PowerMechanical Regulatory Approvals Service Information Moxa Internet Services Following services are provided Moxa Product % EDS-508 Problem Report FormSerial Number Product Return Procedure