Rack Mounting, Chassis Ears | MSI MS-9246 instruction

System Hardware

Rack Mounting

Chassis Ears

1. Insert the chassis ear into the chassis (as marked below).

2. Push it in until it fits firmly. Screw to secure the chassis ear.

3. Follow the same procedures to install the second chassis ear.

2-17

Image 41

MSI MS-9246 manual Rack Mounting, Chassis Ears

Contents

MS-9246 1U Rackmount Server FCC-A Radio Frequency Interference Statement Voir LA Notice D’INSTALLATION Avant DE Raccorder AU Reseau Trademarks Copyright NoticeRevision History Technical Support Safety Instructions Contents Mainboard Hardware Vii Getting Started Packing Checklist Ear Set Rail Set Power Supply Options Top View System Overview Front View Front Bezel LED LED ™ Front Bezel LEDsColor State Description BMC DLED1 Processor Initialization Rear View Rear Bezel Scsi Connector Mouse/Keyboard ConnectorSerial Port VGA Port CPU System Specifications Bios 2D Modes TFT or CRT Video Key Features Onboard Connector/HeaderMSI Server Management Ipmi 1.5 optional BMC Chip MS-9146 v1.X Server Board Mainboard Layout MSI Special Features PC Alert System Hardware Start System Assembly Flowchart Finish Removing the Chassis Cover System Assembly Replacing the Chassis Cover CPU1 CPU2 CPU, Heatsink, and Fan Duct Install the second heatsink Replace the fan duct DDR Memory Memory Bus Features DDR333 Dimm slot population Memory Population RulesDDR266 Dimm slot population PCI Expansion Card System Hardware Optional PCI Riser Card MS-9570 PCI Riser Card OptionalStandard PCI Riser Cards MS-9583, MS-9584 Scsi HDD MS-9246 1U Rackmount Server Serial ATA HDD MS-9246 1U Rackmount Server Chassis Ears Rack Mounting Chassis Rails System Hardware Rack Rails Cable Arm Optional MS-9246 1U Rackmount Server Chassis into the Rack Chassis off the Rack Mainboard Hardware Quick Components Guide CPU1 Central Processing Unit CPU CPU Installation Procedures for Socket Memory MCH Memory Population Rules Memory Speed/CPU FSB Support Matrix Installing DDR Modules JPWR1 Power SupplySSI 24-Pin Power Connector JPWR1 USB1 ConnectorsFront USB Connector USB1 SATA1 SATA2 Serial ATA RAID 0, 1 Connectors SATA1, SATA2 Optional SCSI1/2 Ultra320 Scsi Connectors SCSI1/SCSI2 Optional Serial Port Connector COM Ipmb Power Connector CN4Pin Ipmb Connector CN3 JBAT1 JumpersClear Cmos Jumper JBAT1 Clear Bios Password Jumper J7 Bios Recovery Jumper CN6Clear Event Log Jumper J8 CN6 SO Dimm Small Outline Dimm SlotsPCI Peripheral Component Interconnect Slots CN7 Bios Setup Control Keys Entering Setup General Help F1 Getting HelpMain Menu Sub-Menu Main Menu BarSystem Summary Advanced Exit BootSecurity System Time MainSystem Date Legacy Diskette a Language System Summary Hyper-Threading Technology Processor SettingsAdvanced Advanced Chipset Control Enable Multimedia TimerUSB Host Controller Parallel ATA Sata RAID Enable Native Mode OperationWake On RTC Alarm PCI Configuration Embedded Scsi Optional Peripheral ConfigurationScsi Controller Optional Option ROM Scan Optional Boot-time Diagnostic Screen Boot FeaturesQuickBoot Mode Post Error Pause View DMI Event Log DMI Event LoggingEvent Logging ECC Event Logging Baud Rate Bios Redirection PortFlow Control Console Type BMC Device ID Ipmi Specification VersionBMC Device Version BMC Firmware Version Bios Post Errors Change COM Port SettingBios Post Watchdog OS Boot Watchdog Press Enter to display the System Event Log System Event Log Security Supervisor Password Is/User Password IsSet Supervisor Password/Set User Password Fixed disk boot sector Password on boot CD-ROM Drive, Removable Devices, Hard Drive Boot Exit Appendix a Scsi Bios Setup Optional Selecting the Management Type Entering Scsi BiosSelecting the Scsi Channel Scsi Disk Utilities Configure/View Scsi Controller Settings Scsi Bus Interface Definitions Configure/View Scsi Controller SettingsScsi Controller ID Scsi Controller Parity Additional Options Sync Transfer Rate MB/Sec Enable DisconnectionPacketized QAS Bios Multiple LUN Support Send Start Unit CommandInclude in Bios Scan Advanced Configuration Bios Information Disk Utilities Verify Disk Media Format Disk Adaptec Sata RAID Utility for Intel ICH5R Introduction Adaptec Sata RAID Utility for Intel ICH5R Installing the Driver in a New Windows System Installing the Driver Installing the Red Hat Driver in a New Linux System Installing the Driver in an Existing Windows SystemInstalling Red Hat Linux 7.3 or Installing the Driver in a New Linux System Installing SuSE Linux 8.0 or Supported Browsers Typical, Custom, and Compact Installations Installing Adaptec Storage Manager on Windows Click LAN Settings Configuring Internet Browsers on Windows Select Edit Preferences Sh mount-point/install.sh Installing Adaptec Storage Manager on Linux Using Adaptec Storage Manager Browser Edition Logging Architecture Overview Registering Your Software Installing a Security Certificate Basics Physical Devices Pop-Up Tool Tips Logical Devices MSI Reminds You Using the Array Configuration Utility Adaptec RAID Configuration UtilityFrom the ARC menu, select Array Configuration Utility ACU Managing Arrays Creating Arrays When you are finished, press Done Initializing Disk Drives Using the Disk Utilities ATA GlossaryACU Cache Consistency check commandCapacity Channel Drive LED Fault-tolerant arrayEvent Event log Legacy disk Initialized arrayLogical device Low-level format RAID Volume Spanned volumeSingle-level array Snapshot