Multi-Link ML-100, ML-001 manual Phone Number Programming, Control Panel, Questions Solutions

INSTALLATION

Phone Number Programming

You can program up to 6 Emergency Phone Numbers. When the system is in panic, the control panel will call these phone numbers and announce its status.

The 6 emergency phone numbers include:

-5 voice message phone numbers

-1 Contact ID message phone number

Program the following for Voice Message Phone Numbers

-Phone memory (from 1 to 5), this is where the phone numbers will be stored

-Phone number, up to 29 digits.

-Redial count, this is how many times that phone number will be called, from 1 to 9 times.

-Repeat count, this is how many times the emergency message will be repeated, from 1 to 9 times.

Step	Keys	Function	Description	Note
1	[PROG]	Enter	Enter master password to	3 beeps for valid
		Programming	programming mode	password. 1 long beep
	[MPIN]
		mode		for invalid password.
2	[1]	Select phone		You will hear [Enter
		number		phone memory].
		programming
3	[1] to [5]	Enter phone	During emergency, phone
			memory 1 will be called first,
		memory
			then phone memory 2, 3, 4, and
			5. So phone memory 1 has
			higher priority.
4	[Phone	Enter phone	Phone number can be up to 29	You will hear [Enter
	number]	number	digits.**	Redial].
	+ [Arm]
5	[1] to [9]	Enter Redial	Redial is the number of times	You will hear [Enter
	+ [Arm]	count	that phone number will be	Repeat].
			called. Each phone number
			can have a different redial
			count, from 1 to 9 times.
6	[1] to [9]	Enter Repeat	Repeat is the number of times	You will hear [Phone
	+ [Arm]	count	that voice emergency message	Accepted] indicating the
			will be played, from 1 to 9 times.	phone number and its
			It is recommended to set up	settings have been
			the repeat time to 5 or more.	programmed successfully.

**Note:

You may enter a 3-second pause between digits by pressing [Mute] if needed. You may also enter consecutive multiple pause periods. For example, you may enter a phone number: (123)-456-7890 [Mute] 1234. After the phone number (123)-456-7890 is dialed, it will wait for 3 seconds, then dial 1234, which can be a password to a paging system, or an access code for a phone dialing system.

–10–

TROUBLE SHOOTING

Control Panel

Questions	Solutions
Why I can’t arm my system?	Make sure none of the sensors are
	triggered. You can check this by the zone
	LEDs, none of them should blink.
I cannot arm the system even when no	You need to disarm the system again by
sensor is triggered, and the ARM LED	either entering the password or disarm by
is off.	keychain remote. Although the ARM LED
	is off, but the system is not completely
	disarmed after an alarm was triggered.
	Refer to page 22 on how to completely
	disarm a control panel after an alarm has
	been triggered.
Why the ARM LED keeps flashing?	That means you have not programmed any
	emergency phone numbers. For instructions
	on how to program emergency phone
	numbers, please see page 10.
How do I exit programming mode	You can press the programming button on
when I’m in the middle of it?	the side of the unit to quit programming
	anytime.
When a sensor is triggered, the alarm	You have programmed that sensor in alarm
sounds instantly even it is not armed,	mode, instead of beep mode. Please refer
why is that?	to page 29 for instructions of how to program
	it back to beep mode.
When the alarm is triggered, why	The control panel will stop calling when it
the control panel won’t call all the	is disarmed by any one of the recipients.
programmed phone numbers? It	Disarm can also be done locally thru the
always stops before calling the	keypad on the control panel by entering a
last number.	valid password.
Why the control panel doesn’t beep	You have placed the buzzer mode selector
when a sensor is triggered, while	on the side of the control panel to “II”, this
only the zone LED flashes?	will disable the beeping. Placing it to “I” will
	enable the beeping.
The control panel is in armed mode,	If the triggered sensor is programmed in the
why activating a sensor will not cause	Alert Zone (Bypass Zone), alarm will not
an alarm, or call any emergency phone	sound, and emergency call will not be made
number?	if this sensor is triggered. The control panel
	will only respond when it is disarmed, in
	alert mode.

–47–