Diagnostic Display | Multiquip DCA180SSJU specs

DIAGNOSTIC DISPLAY

First Time Start Up

1.When power is first applied to the diagnostic display, the “Logo” is displayed.

2.The first seven items of the “Main Menu” will be displayed. Touching the “Arrow Buttons” will scroll through the menu selection.

GO TO 1-UP DISPLAY

LANGUAGES

STORED CODES

ENGINE CONFG

SETUP 1-UP DISPLAY

SETUP-4-UP DISPLAY

SELECT UNITS

	2. The “Wait to Start” message will be displayed for engines	3. Touching the right arrow button will scroll down to reveal
	with a pre-startup sequence. Once the “Wait to Start”	the last items of “Main Menu” screen highlighting the
	with a pre-startup sequence. Once the “Wait to Start”	next item down.
	message is no longer displayed the operator may start	next item down.
	message is no longer displayed the operator may start
	the engine. Note: Displays only when SAE J1939
	message is supported by engine manufacturer.
		ADJUST BACKLIGHT
		ADJUST CONTRAST
		UTILITIES
	WAIT TO
	START
	PREHEAT

3. Once the engine has started the single engine parameter is displayed.

4. Touch the Arrows” to scroll to the desired menu item or touch “Menu” to exit the Main menu and return to the engine parameter display.

0

1500

3000

1800 RPM

ENG RPM COOL TEMP

Main Menu Navigation

							98%

	0				3000
	0	1500			3000
		1800 RPM					LOAD RPM

							14.2
			COOL TEMP
	ENG RPM
	ENG RPM						BATT VOLT

Selecting a Language

1000 RPM

ENG RPM

57 PSI

OIL PRES

1.Starting at the single or four engine parameter display, touch “Menu”.

1.Starting at the main menu display use the “Arrows to scroll to the “Language” menu and once highlighted touch the “Enter” button.

							98%

	0				3000
	0	1500			3000
		1800 RPM					LOAD RPM

							14.2
			COOL TEMP
	ENG RPM
	ENG RPM						BATT VOLT

1000 RPM

ENG RPM

57 PSI

OIL PRES

GO TO 1-UP DISPLAY

LANGUAGES STORED CODES ENGINE CONFG SETUP 1-UP DISPLAY SETUP-4-UP DISPLAY SELECT UNITS

DCA-180SSJU — OPERATION AND PARTS MANUAL — REV. #3 (02/01/10) — PAGE 23

Image 23

Multiquip DCA180SSJU operation manual Diagnostic Display

Contents

Model DCA180SSJU 60HZ Generator Parts List NO. M3870301004 Proposition 65 Warning Nhtsa Reporting Safety Defects Table of Contents MQ Power DCA-180SSJU Whisperwatttm Generator Ordering parts has never been easier Parts Ordering Procedures Generator Specifications Specifications Dimensions Dimensions TOP, Side and Front Potential hazards associated with the operation of this Safety Message Alert SymbolsConjunction with Safety This generator, other property Always wear approved protectionProtection Drugs or alcohol General SafetyResult causing severe Rules for Safe Operation Generator Grounding Electrical Safety Avoid eye irritation Maintenance SafetyBattery Safety Use the following guidelines when handling the battery Emergencies Towing & Transporting SafetyDOT Generator Decals Generator Decals Generator Decals Cont inued Typical Generator Grounding Application Installation Mounting Outdoor InstallationIndoor Installation When connecting the generator General Information Generator Major Components Major Components Display Parameters Diagnostic DisplayMenu Button Press this button to enter or exit menu screens Main Menu Navigation Engine. Note Displays only when SAE J1939First Time Start Up Next item down To make a selection Diagnostic CodeStored Fault Codes Engine Configuration Data Diagnostic Display 24 DCA-180SSJU Operation and Parts Manual REV. #3 02/01/10 Auxiliary Gage Fault Active Fault Codes Damage Backlight AdjustmentShut Down Codes Contrast is highlighted Contrast AdjustmentIntensity Select Units Setup 1- Up Display Up display function Once the Setup 1-up Display menu icon has been Automatic Scan on Touch the Enter Button and a list of parameters will appear Setup 4-Up DisplaySelect the 4-Up Custom Setup from the 4-Up Setup menu Utilities Engine OIL Temperature 34 DCA-180SSJU Operation and Parts Manual REV. #3 02/01/10 Touch the Menu Button Highlight it, then touch Enter Touch the Menu button again to return to the MainMenu Press and hold the Menu button for approximately 3 seconds Glossary Troubleshooting informationECU did not respond to the PowerView request No parameter selected for this 4- UP quadrant Circuit breaker Position on To restore power toGenerator Control Panel Button on the overcurrent relay and place Fuel Gauge Indicates amount of diesel fuel available Engine Operating Panel Unit. This is considered a FaultAuto On/Off Engine Controller Mpec Engine by initializing Output Terminal Familiarization Output Terminal Panel FamiliarizationAre considered Counter-clockwise will Voltage Removing the Plastic Face Plate Hard Wire Hookup PanelVAC Gfci Receptacles Pressing Over Current Relay Connecting Loads Load Application Single Phase LoadThree Phase Load System, amust install an Maximum Amps Generator OutputsGenerator Output Voltages Voltage Change-Over Board Are Generator OUTPUTS/ Gauge ReadingAC Ammeter Gauge Reading Show a reading when 1Ø-240V Uvwo Terminal Output Voltages Output Terminal Panel ConnectionsUvwo Terminal Output Voltages 3Ø-240V Uvwo Terminal Output Voltages Uwvo Output Terminal Lugs 1Ø-277V Connections 3Ø-480 Uvwo Output Terminal Voltages Fuel Check SetupCircuit Breakers Lubrication Oil Refueling Refueling ProcedureONLY! use Operation Freezing Weather Cleaning the RadiatorAir Cleaner Fan Belt Tension Coolant Antifreeze Alternator BatteryBattery Cable Installation Wiring Starting Manual Generator START-UP Procedure ManualBefore Starting Speed switch OFF/RESET position Ammeter will Starting Auto ModeWhen the generator is set Auto mode, the generator will On position Figure Generator START-UP Procedure Auto Mode OFF/RESET position Emergency Shutdown Procedure Generator SHUT-DOWN ProceduresNormal Shutdown Procedure Maintenance Engine Replacing Oil Filter Cleaning the Fuel StrainerAir Removal Check Oil Level To ensure adequate starting Maintenance HEATER/CHARGERCommercial power to theand Trailer Maintenance Maintenance Trailer Actuator Brake AdjustmentBrakes Hydraulic Surge Brakes Suspension Tires/Wheels/Lug NutsTire Wear/Inflation Use an pneumatic air Lug Nut Torque Requirements Trailer/Towing Vehicle Wiring Diagram Trailer Wiring Diagram Generator Wiring Diagram Generator Wiring Diagram Engine Wiring Diagram DCA-180SSJU Engine Wiring Diagram Generator Troubleshooting Troubleshooting Generator Engine Controller Troubleshooting Mpec Troubleshooting Engine Controller DCA-180SSJU Operation and Parts Manual REV. #3 02/01/10 Explanation of Code in Remarks Column Sample Parts List Suggested Spare Parts Part number on this Suggested Spare Parts list Generator Assy 0018205020 C01100006020601842334 0601823282 Control Panel Assy 022100165 M4223000303M4223000404 022100100 Control BOX Assy 0601870423 M32130013020601809666 0027106018 78 DCA-180SSJU Operation and Parts Manual REV. #3 02/01/10 0027106016 M42605000030602202592 29A 0030006000 Engine and Radiator Assy Part Name QTY Remarks Engine and Radiator ASSY. Part Name Output Terminal Assy Output Terminal Assy 0039320000 M3230700113M9220100914 M9220101004 86 DCA-180SSJU Operation and Parts Manual REV. #3 02/01/10 0601812538 M426060010425-1 022100150 0019206020 Battery Assy 0602220921 0602220196M9310500404 M9103000504 Muffler Assy 0602325066 M43301005020016910025 M4333000303 Fuel Tank Assy 0605516090 M43630001020605505070 0605501069 Enclosure Assy Enclosure Assy M4423000312 M4413000302M1413400004 0019208020 Enclosure ASSY. Enclosure ASSY. 0021806016 003790600028A 0041206000 M9113000002 98 DCA-180SSJU Operation and Parts Manual REV. #3 02/01/10 52A M4493403904 M445300120351A M4493403804 M4453001303 Rubber Seals Assy 0228901260 02292012400228900945 0228901200 Nameplate and Decals Assy M3550002702 M4550000303M9520100304 M9520100603 Freight Policy Terms and Conditions of Sale Parts DCA-180SSJU Operation and Parts Manual REV. #3 02/01/10 HERE’S HOW to GET Help