Remote Control Optional, Radio Remote Control

REMOTE CONTROL (OPTIONAL)

The LS600 Concrete Pump has a remote control feature that allows the pump to be remotely controlled. If desired, the pump can be operated via a receiver/transmitter (radio) or a hardwire method, which utilizes a 25-ft. extension cable. Contact MQ Sales Department to order remote control.

LS600 PUMP — OPERATION

4.Reinstall the control panel and tighten the 2 screws.

5.On the top of the unit, to the right of the control box (Figure 36), hammer out the knock-out hole and install the remote antenna.

Radio Remote Control

Installation of the Radio Remote Control Assembly

1.Remove the two screws on the digital control panel of the pump. See Figure 33.

CONTROL BOX

VOLUME

DIRFELOW

CTION

CONTROL	ON
	OFF
	START
	IGNITION

REMOTE

ANTENNA

KNOCK-OUT

HOLE

ANTENNA

CONNECTOR

CABLE

REAR OF CONTROL BOX

CONTROL BOX CONNECTOR

REMOVE 2 SCREWS

Figure 33. Removing Screws from Control Panel

2.Tilt and slowly pull out the control panel and place on top of box to gain access inside the box. See Figure 34.

Figure 34. Pulling Out Control Panel

3.Install the wireless remote module with the 2 screws and nuts provided inside the control panel. Connect the 3-wire connector from the wireless remote module to the electronic control unit. See Figure 35.

Figure 36. Antenna Installation

6.Connect the antenna cable to the connector on the rear of the control box (Figure 36).

Radio Remote Control Buttons Operation

The pumping operation can be performed by radio remote control (Figure 37). Before using remote control, move the Pumping Control Switch on the control box to the REMOTE position.The buttons on the remote control have the following functions.

ON/OFF - Turns the power on or off. When power is on the power LED lights red. If the battery LED turns red, 9V battery needs to be replaced.

E-STOP- Turns off the pump completely in an emergency.

PUMP ON/OFF - Starts and stops the forward pumping.

PUMP REV - momentarily pumps in reverse direction.

VOLUME (+) - used to increase the pumping volume.

VOLUME (-)- used to decrease the pumping volume.

SCREWS AND NUTS

E-STOP

ELECTRONIC

OFF

PUMP PUMP

POWER LED

CONTROL

UNIT

WIRELESS

REMOTE

MODULE

CONNECTOR

REV ON/OFF

BATTERY LED

VOLUME VOLUME

NOTE: OLDER MODELS

MAY INDICATE FLOW

INSTEAD OF VOLUME

Figure 35. Installing Remote Control Module

Figure 37. Radio Remote Control

PAGE 30 — MAYCO LS600 PUMP — OPERATION AND PARTS MANUAL — REV. #4 (9/15/11)

LS600 specifications

The Multiquip LS600 is a robust and efficient light tower designed to provide reliable lighting solutions for various applications, including construction sites, outdoor events, and emergency services. This advanced model blends cutting-edge technologies with user-friendly features, ensuring that users have the illumination needed to get the job done safely and effectively.

At the heart of the LS600 is its powerful lighting system, which utilizes four high-efficiency LED lights. These lights deliver an impressive total output of up to 600,000 lumens, providing extensive coverage and bright illumination across large areas. The energy-efficient LEDs not only offer superior brightness but also contribute to lower operational costs and extended run times compared to traditional lighting systems.

One of the standout features of the LS600 is its extendable mast. The mast can be raised to a height of 30 feet, allowing the lights to be positioned at an optimal height for maximum visibility. This flexibility is essential for overcoming obstacles and ensuring that all areas are uniformly lit. The mast is also designed for quick and easy deployment, enabling users to set up the light tower rapidly and focus on their primary tasks.

The LS600 is powered by a reliable and fuel-efficient diesel engine, which provides consistent performance even in demanding conditions. The engine is equipped with advanced technologies to enhance fuel efficiency and reduce emissions, making it an environmentally friendly option for users who are conscious of their carbon footprint. The light tower has a long run time, capable of operating for extended periods without the need for frequent refueling.

Portability is another key characteristic of the Multiquip LS600. The unit is designed with a rugged frame and sturdy wheels, allowing for easy transport across various terrains. This mobility is complemented by a compact design that facilitates storage and handling, making it an ideal choice for rental companies and contractors.

In conclusion, the Multiquip LS600 stands out as a versatile and powerful light tower, engineered to deliver exceptional performance and reliability. Its high-lumen LED lighting, extendable mast, robust diesel engine, and portability make it a top choice for those in need of dependable lighting solutions in challenging conditions. Whether illuminating a busy construction site or enhancing safety at an outdoor event, the LS600 is equipped to handle a wide range of lighting demands with efficiency and ease.

Multiquip LS600 Remote Control Optional, Reinstall the control panel and tighten the 2 screws

Models: LS600