LS600 PUMP — RULES FOR SAFE OPERATION

■NEVER run engine without air filter. Severe engine damage may occur.

■ALWAYS be sure the operator is familiar with proper safety precautions and operation techniques before using pump.

■ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children.

■DO NOT operate this equipment unless the hopper grate, guards and safety devices are attached and in place.

■CAUTION must be exercised while servicing this equipment. Rotating and moving parts can cause injury if contacted.

■Keep all inexperienced and unauthorized people away from the equipment at all times.

■Before start-up, check the hopper and remove all foreign matter and debris.

■DO NOT use worn or damaged hose couplings, inspect all hoses and couplings for wear. Replace any worn or defective hose or couplings immediately.

■Keep hands out of the hopper when the engine is running.

■DO NOT disconnect hose couplings or nozzle while under pressure. Relieve pressure by activating the reverse function switch located on the control panel.

■Unauthorized equipment modifications will void all warranties.

■Check all fasteners periodically for tightness. Also check towing tongue bolt, lock nut and wheel lug nuts for wear.

■Test the pump's ON/OFF switch. The purpose of this test is to shut down the engine.

■Refer to the DEUTZ Engine Owner's Manual for engine technical questions or information recommended by Multiquip for this equipment. Damage to the equipment and or injury to user may result.

■Always use properly rated hoses and clamps — 1500 PSI and higher.

TRANSPORTING

■ALWAYS shutdown engine before transporting the pump.

■Tighten fuel tank cap securely to prevent fuel from spilling.

■Drain fuel when transporting pump over long distances or bad roads.

Towing

■Before towing, check the hitch and secure the safety chain to the towing vehicle.

■When towing, an adequate safety chain must be fastened to the frame, refer to Towing Guidelines.

■Tow only with a vehicle and hitch rated to pull a 6,000 lbs. load.

■If unit is equipped with ball hitch coupler, use only 2" all steel ball rated for minimum of 6,000 lbs. Use 1" hardened steel pull pin, if not equipped with ball hitch.

■This equipment shall not be towed or operated by individuals who cannot read understand the signs, decals or operating instructions.

■When towing at night, always have rear tail lights ON.

■DO NOT tow unit with hopper full of material.

■DO NOT tow unit with hoses attached.

■DO NOT tow unit in excess of 55 MPH on highways.

MAINTENANCE SAFETY

■NEVER lubricate components or attempt service on a running pump .

■ALWAYS allow the pump a proper amount of time to cool before servicing.

■Keep the pump in proper running condition.

■Fix damage to the pump immediately and always replace broken parts.

■Dispose of hazardous waste properly. Examples of potentially hazardous waste are used motor oil, fuel and fuel filters.

■DO NOT use plastic containers to dispose of hazardous waste.

MAYCO LS600 PUMP — OPERATION AND PARTS MANUAL — REV. #4 (9/15/11) — PAGE 9

Page 8 Page 10
Page 9
Image 9
Multiquip LS600 manual Transporting, Towing, Maintenance Safety
Page 8 Page 10

LS600 specifications

The Multiquip LS600 is a robust and efficient light tower designed to provide reliable lighting solutions for various applications, including construction sites, outdoor events, and emergency services. This advanced model blends cutting-edge technologies with user-friendly features, ensuring that users have the illumination needed to get the job done safely and effectively.

At the heart of the LS600 is its powerful lighting system, which utilizes four high-efficiency LED lights. These lights deliver an impressive total output of up to 600,000 lumens, providing extensive coverage and bright illumination across large areas. The energy-efficient LEDs not only offer superior brightness but also contribute to lower operational costs and extended run times compared to traditional lighting systems.

One of the standout features of the LS600 is its extendable mast. The mast can be raised to a height of 30 feet, allowing the lights to be positioned at an optimal height for maximum visibility. This flexibility is essential for overcoming obstacles and ensuring that all areas are uniformly lit. The mast is also designed for quick and easy deployment, enabling users to set up the light tower rapidly and focus on their primary tasks.

The LS600 is powered by a reliable and fuel-efficient diesel engine, which provides consistent performance even in demanding conditions. The engine is equipped with advanced technologies to enhance fuel efficiency and reduce emissions, making it an environmentally friendly option for users who are conscious of their carbon footprint. The light tower has a long run time, capable of operating for extended periods without the need for frequent refueling.

Portability is another key characteristic of the Multiquip LS600. The unit is designed with a rugged frame and sturdy wheels, allowing for easy transport across various terrains. This mobility is complemented by a compact design that facilitates storage and handling, making it an ideal choice for rental companies and contractors.

In conclusion, the Multiquip LS600 stands out as a versatile and powerful light tower, engineered to deliver exceptional performance and reliability. Its high-lumen LED lighting, extendable mast, robust diesel engine, and portability make it a top choice for those in need of dependable lighting solutions in challenging conditions. Whether illuminating a busy construction site or enhancing safety at an outdoor event, the LS600 is equipped to handle a wide range of lighting demands with efficiency and ease.
Top Page Image Contents