LS600 PUMP — PUMPING INFORMATION

Usingthis procedure willmakeiteasier topumpthrough the clean hose. Note: Once the concrete has reached the end of the hose, do not apply any more water in this manner as this procedure is used for starting only.

6.Hose sizing is very important:We strongly recommend on harsh mixes, vertical pushes, stiff concrete, shotcrete, long pushes, that a 2 -1/2” line be used as far as possible.The advantages of using the 2 -1/2”line are improved pumpability, less pumping pressure and less wear on the pump.

7.Following the pump operation, proper wash out of all materials or “build-up” within the pump manifold and hoses will prevent problems when starting the next job.

8.A thorough inspection of the drive components and greasing of all bearings after each job will ensure adequate lubrication and service to the pump which is normally operating in wet, gritty conditions.

Over-greasing any bearing on your Mayco pump will not damage the bearing.

CLEARING THE SYSTEM AFTER MIX SET UP

If, for any reason, the mix should set up in the system, the following procedure is suggested:

1.Disconnect the hose from the pump and wash the pump out immediately.

WARNING - HOSE/LINE PRESSURE

When disconnecting hoses, use EXTREME CAUTION! The hose is under pressure!

2 Reconnect the hose and fill the hopper with water.

3.Reconnect the hose and fill the hopper with water. DO NOT try to push all the concrete out of all of the hose lines at one time.

For example: If you had 200 ft. of system out, you would disconnect each hose. Clean it out by pushing water through the first hose off the pump, then continue progressing through all the hoses, until all the system is clean.

4.If waiting time is excessive, it would be wise to wash out the pump and hoses and start over when the new truck arrives. This can be avoided by being observant to the pump and system, also taking into consideration the above actors (A through D) affecting the mix.

CLEARING CONCRETE BLOCKAGE

WARNING - BLOCKAGES

If you repeatedly pull the throttle all the way out and try to force your pump to push through blockages due to separation of material in the hose or manifold, you will soon have breakdowns and costly repairs which are not covered under warranty.

If a blockage occurs, find where it is and clear it before further pumping.DO NOT increase the engine speed to clear the blockage. Increasing the engine speed will only compound the problem.

If a blockage occurs in a hose, walk the hose until you find the point of trouble. The hose will be soft immediately past the blockage. To clear the blockage:

1.Disconnect the hose at the first coupling past the blockage.

WARNING - HOSE LINE PRESSURE

Use extreme care! The hose line is under pressure and can cause serious injury.

2.Elevate the hose at that point with the blockage area hanging down.

3.Using a hammer, you can pound the downstream edge of the packed area until it is free to flow.Shake all of the sand and gravel out to the end of the hose.

4.Before reconnecting the hose, start the pump and run a small amount of concrete out to the end of the hose. This will assure that all of the separation is out of the hose.

Damaged hoses with internal restrictions can cause blockages.

PAGE 34 — MAYCO LS600 PUMP — OPERATION AND PARTS MANUAL — REV. #4 (9/15/11)

Page 34
Image 34
Multiquip LS600 manual Clearing the System After MIX SET UP, Clearing Concrete Blockage

LS600 specifications

The Multiquip LS600 is a robust and efficient light tower designed to provide reliable lighting solutions for various applications, including construction sites, outdoor events, and emergency services. This advanced model blends cutting-edge technologies with user-friendly features, ensuring that users have the illumination needed to get the job done safely and effectively.

At the heart of the LS600 is its powerful lighting system, which utilizes four high-efficiency LED lights. These lights deliver an impressive total output of up to 600,000 lumens, providing extensive coverage and bright illumination across large areas. The energy-efficient LEDs not only offer superior brightness but also contribute to lower operational costs and extended run times compared to traditional lighting systems.

One of the standout features of the LS600 is its extendable mast. The mast can be raised to a height of 30 feet, allowing the lights to be positioned at an optimal height for maximum visibility. This flexibility is essential for overcoming obstacles and ensuring that all areas are uniformly lit. The mast is also designed for quick and easy deployment, enabling users to set up the light tower rapidly and focus on their primary tasks.

The LS600 is powered by a reliable and fuel-efficient diesel engine, which provides consistent performance even in demanding conditions. The engine is equipped with advanced technologies to enhance fuel efficiency and reduce emissions, making it an environmentally friendly option for users who are conscious of their carbon footprint. The light tower has a long run time, capable of operating for extended periods without the need for frequent refueling.

Portability is another key characteristic of the Multiquip LS600. The unit is designed with a rugged frame and sturdy wheels, allowing for easy transport across various terrains. This mobility is complemented by a compact design that facilitates storage and handling, making it an ideal choice for rental companies and contractors.

In conclusion, the Multiquip LS600 stands out as a versatile and powerful light tower, engineered to deliver exceptional performance and reliability. Its high-lumen LED lighting, extendable mast, robust diesel engine, and portability make it a top choice for those in need of dependable lighting solutions in challenging conditions. Whether illuminating a busy construction site or enhancing safety at an outdoor event, the LS600 is equipped to handle a wide range of lighting demands with efficiency and ease.