National Instruments ICDM Introduction to MIMO Design

© National Instruments Corporation 11-1 Xmath Interactive Control Design Module

11

Introduction to MIMO Design

The following chapters describe the use of ICDM for MIMO design. NI

assumes the reader is familiar with the use of ICDM for SISO design. In

many cases, the texts describe the differences between SISO and MIMO

design.

This chapter provides an introduction to MIMO design. ICDM

automatically switches between SISO and MIMO modes depending on the

plant that is read in. To try out the MIMO features described here and in the

next two chapters, you must first either read in a MIMO plant, or select the

MIMO plant from the Default Plants submenu in the Read Plant menu.

Basic Terminology for MIMO Systems

The following sections define the basic terminology and notation used to

refer to MIMO systems in ICDM, for analysis and plotting. The LQG/H∞

Synthesis window uses additional terminology described in Chapter 12,

LQG/H-Infinity Synthesis.

Feedback System Configuration

ICDM uses the feedback configuration shown in Figure 11-1. The

configuration and signal names agree with the standard SISO configuration

shown in Figure 2-1, with two differences. Here, all signal paths represent

vector signals, whereas in the SISO setup, the signals are scalar. There is

also a new signal, dact, that subtracts from the actuator signal. This signal

can be thought of as an actuator-referred disturbance signal, an actuator

noise, or just a fictitious input that allows you to see the transfer functions

from the actuator to various other signals.

The equations describing this system are:

where, as shown in Figure11-1:

y denotes the plant output or sensor signal, which is a vector of size ny

yPud

act

–()=uCe=ery–=

Contents

Main Page Important Information Warranty Copyright Trademarks Patents Conventions Contents Chapter 1 Introduction Chapter 2 Introduction to SISO Design Chapter 3 ICDM Main Window Chapter 4 PID Synthesis Chapter 5 Root Locus Synthesis Chapter 6 Pole Place Synthesis Chapter 7 LQG Synthesis Chapter 8 H-Infinity Synthesis Chapter 9 Chapter 10 Alternate Plant Window Chapter 11 Introduction to MIMO Design Chapter 12 LQG/H-Infinity Synthesis Page Introduction Using This Manual Document Organization Page Commonly-Used Nomenclature Related Publications MATRIXx Help ICDM Overview SISO Versus MIMO Design Starting ICDM Page Introduction to SISO Design SISO Design Overview Basic SISO Terminology Page Overview of ICDM ICDM Windows ICDM Main Window PID Synthesis Window Root Locus Synthesis Window Pole Place Synthesis Window LQG Synthesis Window H-Infinity Synthesis Window Alternate Plant Window Key Transfer Functions and Data Flow in ICDM Summary Origin of the Controller What the ICDM Main Window Plots Show Controller/Synthesis Window Compatibilities Page Using ICDM G G Page Zooming Data-Viewing Plots Interactive Plot Re-ranging Graphically Manipulating Poles and Zeros Editing Poles and Zeros Editing Poles and Zeros Graphically Complex Poles and Zeros Isolated Real Poles and Zeros Nonisolated Real Poles and Zeros and Almost Real Pairs Adding/Deleting Poles and Zeros Adding/Deleting Pole-Zero Pairs Page ICDM Main Window Communicating with Xmath Most Common Usage Default Plants Saving and Restoring an ICDM Session Reading Another Plant into ICDM Reading a Controller from Xmath into ICDM Writing the Plant Back to Xmath Writing the Alternate Plant back to Xmath Writing a Controller on the History List to Xmath ICDM Plots Selecting Plots Ranges of Plots Plot Magnify Windows Page Selecting a Synthesis or History Window Edit Menu PID Synthesis PID Controller Terms Toggling Controller Terms On and Off Page Opening the PID Synthesis Window Manipulating the Controller Parameters Time Versus Frequency Parameters Ranges of Sliders and Plots Controller Term Normalizations Integral Term Normalization Derivative Term Normalization Rolloff Term Normalization Root Locus Synthesis Overview Page Opening the Root Locus Synthesis Window Terminology Plotting Styles Phase Contours Magnitude Contours Slider and Plot Ranges Manipulating the Parameters Design Adding a Pole-Zero Pair Deleting Pole-Zero Pairs Interpreting the Nonstandard Contour Plots Page Pole Place Synthesis Pole Place Modes Normal Mode Integral Action Mode State-Space Interpretation Opening the Pole Place Window Manipulating the Closed-Loop Poles Time and Frequency Scaling Butterworth Configuration Editing the Closed-Loop Poles Slider and Plot Ranges LQG Synthesis LQG Synthesis Window Anatomy Page Synthesis Modes Opening the LQG Synthesis Window Setup and Terminology Standard LQG (All Toggle Buttons Off) Exponential Time Weighting Output Weight Editing State-Space Interpretation Manipulating the Design Parameters Graphically Page H-Infinity Synthesis H-Infinity Synthesis Window Anatomy Page Opening the Synthesis Window Setup and Synthesis Method Central H-Infinity Controller Output Weight Editing Manipulating the Weight Transfer Function Infeasible Parameter Values Page History Window Saving the Current Controller on the History List Opening the History Window History Window Anatomy Selecting the Active Controller Editing the Comments Deleting History List Entries To Continue Designing from a Saved Controller Cycling Through Designs Writing a Saved Design to Xmath Page Alternate Plant Window Role and Use of Plant and Alternate Plant Displaying the Alternate Plant Responses Alternate Plant Window Anatomy Page Normalization Manipulating the Parameters Using the Alternate Plant Window Robustness to Plant Variations Adding Unmodeled Dynamics Ranges of Sliders and Plot Introduction to MIMO Design Basic Terminology for MIMO Systems Feedback System Configuration Transfer Functions Page Page Overview of ICDM for MIMO Design ICDM MIMO Windows Main Window MIMO Plot Window Alternate Plant Window (MIMO Version) Page LQG/H-Infinity Synthesis LQG/H-Infinity Main Window LQG/H-Infinity Weights Window Page Page Decay Rate Window H-Infinity Performance Window Frequency Weights Window Synthesis Modes and Window Usage Opening the LQG/H-Infinity Synthesis Window Setup and Terminology Page Chapter 12 LQG/H-Infinity Synthesis Xmath Interactive Control Design Module 12-10 ni.com Figure 12-6. LQG/H-Infinity Control Design Configuration w How to Select w, u, y, and z H-Infinity Solution Page Main Window Page Multi-Loop Synthesis Multi-Loop Window Anatomy Page Setup and Synthesis Method Multi-Loop Versus Multivariable Design Page Page Page Opening the Multi-Loop Synthesis Window Designing a Multi-Loop Controller Graphical Editor Selecting and Deselecting Loops Editing and Deleting Loops Loop Gain Magnitude and Phase A Using an Xmath GUI Tool Overview Interacting with a GUI Application GUI Functions GUI Objects Page Page Page B Technical Support and Professional Services Index A B C D G H I K L R S T W Z