10. Appendix
xTroubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Power Indicator
| Indicator Condition |
| Projector Condition | Note | ||
|
| Off |
| The main power is off | – | |
|
|
|
|
|
|
|
Blinking light |
| Green blinking |
| 0.5 sec ON, | The projector is getting ready to turn on. | Wait for a moment. |
|
|
|
| 0.5 sec OFF |
|
|
|
|
|
| 2.5 sec ON, | Off Timer or Sleep Timer is active. | – |
|
|
|
| 0.5 sec OFF |
|
|
|
| Orange blinking |
| 0.5 sec ON, | The projector is cooling down. | Wait for a moment. |
|
|
|
| 0.5 sec OFF |
|
|
|
|
|
| 2.5 sec ON, | On Timer is active. | – |
|
|
|
| 0.5 sec OFF |
|
|
Steady light |
| Green |
| The projector is turned on. | – | |
|
| Orange |
| The projector is in Standby or Idle. | – | |
Status Indicator |
|
|
| |||
|
|
|
|
| ||
| Indicator Condition |
| Projector Condition | Note | ||
|
| Off |
| Normal | – | |
|
|
|
|
|
| |
Blinking light |
| Red blinking |
| 1 cycle (0.5 sec ON, | Lens hood or lamp cover error | Replace the lens hood or the lamp cover |
|
|
|
| 2.5 sec OFF) |
| correctly. |
|
|
|
| 2 cycle (0.5 sec ON, | Temperature error | The projector is overheated. Move the |
|
|
|
| 0.5 sec OFF) |
| projector to a cooler location. |
|
|
|
|
|
|
|
|
|
|
| 3 cycle (0.5 sec ON, | Power error | Power unit will not work correctly. |
|
|
|
| 0.5 sec OFF) |
|
|
|
|
|
| 4 cycle (0.5 sec ON, | Fan error | Cooling fan has stopped. Contact your |
|
|
|
| 0.5 sec OFF) |
| dealer. |
Steady light |
| Red (GT6000 only) |
| Circuit error | An error occurs in the circuit. Consult | |
|
|
|
|
|
| your dealer. |
|
| Orange |
| Control key locked | You have pressed control panel key when | |
|
|
|
|
|
| Control Key Lock is enabled. |
|
| Green |
| Idle condition | – | |
|
|
|
|
| ||
Lamp 1/2 Indicator |
|
|
| |||
|
|
|
|
| ||
| Indicator Condition |
| Projector Condition | Note | ||
|
| Off |
| Light off | – | |
Blinking light |
| Red blinking |
| 2.5 sec ON, | Lamp has reached its end of life. Lamp | Replace the lamp. |
|
|
|
| 0.5 sec OFF | replacement message will be displayed. |
|
|
|
|
| 1 cycle (0.5 sec ON, | No lamp | Lamp is not installed. Turn off the power |
|
|
|
| 2.5 sec OFF) |
| and install lamp. |
|
|
|
| 6 cycle (0.5 sec ON, | Lamp error | Lamp fails to light. Wait a full minute and |
|
|
|
| 0.5 sec OFF) |
| turn on the power again. If this will not |
|
|
|
|
|
| solve the problem, consult your dealer. |
|
|
|
| 7 cycle (0.5 sec ON, | Lamp data error | Fails to read lamp data. |
|
|
|
| 0.5 sec OFF) |
| Consult your dealer. |
|
| Green blinking |
| Wait for a moment. | ||
|
| Orange blinking |
| Switching from Lamp 1 to 2 | Wait for a moment. | |
Steady light |
| Red |
| Lamp has been used beyond its limit. The | Replace the lamp. | |
|
|
|
|
| projector will not turn on until the lamp |
|
|
|
|
|
| is replaced. |
|
|
| Green |
| Lamp mode is set to Normal mode | – | |
|
|
|
|
|
| |
|
| Orange |
| Lamp mode is set to Eco mode. | – | |
|
|
|
|
|
|
|
