Radl, Smic, Setting MIC ON/OFF | NEC NDA-24233 specification

VisuaLink 128/384 Engineering GuideConsole Command List

RADL

Checking Audio Mode Setting

2-4

Description:	Checks the current audio delay setting
Command Format:	RADL p1 p2
	p1:	64		:	56/64kpbs
		2x64		:	2x56/2x64 kbps
		3B		:	168/192kbps
		4B		:	224/256kbps
		5B		:	280/320kbps
		6B		:	336/384kbps
	p2:	TX		:	Transmission side
Response:	Normal Response:		p1 OK
			p1: 000 - 024:3-digit in decimal fixed (10msec step)

Error Response: ERR01

ERR05

ERR49

ERR87

Note: If VL128, setting 3B to 6B at p1 results in error.

SMIC

Setting MIC ON/OFF

2-5

Description:

Sets transmitted audio from a microphone to either ON or OFF

Command Format: SMIC p1

p1: ON : MIC ON OFF : MIC OFF

Response:	Normal Response:	OK
	Error Response:	ERR01
		ERR07
		ERR85
		ERR87

NDA-24233 Issue 2

Page 3-11

Image 37

NEC NDA-24233 manual Radl, Smic, Setting MIC ON/OFF

Contents

VisuaLink 128/384 Liability Disclaimer Exhibit J1 FCC Requirements USA If Problems Arise CSA Requirement Page Table of Contents Nbzs Itcs Icst VisuaLink 128/384 Engineering GuideTable of Contents List of Tables Summary PrefaceCommunication Outline Physical/Electrical lnterface Name Direction Features Data Format Communication FormatStart CII PTY Stop Transmit Carriage Return Code ODH Command FormatResponse Format Transmit Carriage Rerun Code ODH Command/Response Procedure Communication ProcedureAbnormal Handshake Procedure Chapter VisuaLink 128/384 Engineering Guide Connecting and Incoming Call Control Basic Sequence This page is for your notes Audio Command Video CommandLine Setting Command Isdn Registering/Setting Command Data CommandCamera related Registering/Setting Command Communication Status Reading Command Serial Port Control Command Registering Local Location Name CommandAcquiring Version Command Maintenance Command Audio Training Command Model Identification CommandIsdn Control Command Camera Control Command Alarm Status Report Command Communication Status Report CommandVideo Status Report Command Participating Status Report Command Multi-Screen Related Report Command Multi-point Related Report CommandMicrophone Command System Error Command Command Name Command Number Command Detailed Format Checking Video Format Setting Setting Video FormatVideo Commands Svfm Checking Picture-in-Picture Setting Setting Picture-in-PictureSpip Rpip Checking Video Input Setting Setting Video Input SwitchSsnd Rsnd Checking Monitor Output Video Setting Setting Monitor Output VideoSdsp Rdsp Setting/Checking PIP Image when Snapshot is Viewed Setting/Checking PIP Display FormatSpdp Spsw S263 Setting H.263 Setting/Checking Video PriorityScpi R263 Checking H.263 Setting Checking Audio Mode Setting Setting Audio ModeSamd Ramd Sadl Setting Audio Delay Radl Setting MIC ON/OFFSmic Svol RmicRvol Checking Audio Input/Output Port Setting Setting Audio Input/Output PortSasw Rasw Checking Audio or Audio/VideoOutput Mute Setting Sets Audio or Audio/Video Outgoing Mute SettingSmmt Rmmt Smtc Sets Audio or Audio/Video Mute SettingRmtc Rmtc Checking Network Type Setting P x 64/56 Setting Network Type P x 64/56Snet Rnet Checking Transmission Line Type Setting Setting Transmission Line TypeNnss Nnsi Checking Transmission Line Speed Setting Setting Transmission Line SpeedSlsp Rlsp Description Setting Low Speed Data LSD port speed Setting LSD SpeedSDM2 Setting MLP Speed Checking LSD Speed SettingRDM2 SDM3 RDM3 Checking MLP Speed SettingRDM3 Registering My Number Ndss Checking My Number Registration Ndsr Registering Speed Dial Mdst Checking Speed Dial Registration Mdrd Checking Incoming Call Buzzer Setting Setting Incoming Call BuzzerNbzs Nbzi Sinc Setting Incoming Call Mode Srng Setting/Checking Incoming Call Buzzer at Auto Answer ModeSpid Registering Spid Checking Spid Rpid Cpps Registering Camera Preset PositionCpns Registering Talker Name Checking Camera Model Setting Setting Camera ModelScmk Rcmk Read Manufacturer Code RmacRmac NEC Rmod Read Common Mode During CommunicationRmod QCIF/FCIF Rpna R221 Read H.221 Synchronous StatusRead Remote Site Name at Point-to-Point Rpna Read Participating Conference Status RcstRcst MLP CPU/VIDEO alarm Read Alarm Status 1Line alarm H221 alarm Bonding alarm Read Alarm Status 2Test status Rlam Read Communication/Alarm HistoryRlam a Registering Local Site Name 10-1 Mrns Checking Serial Port Setting 11-2 Setting Serial Port 11-1Ssio Rsio Requesting Software Version 12-1 RverRver Checking Local Loopback Setting 13-2 Setting Local Loopback 13-1Sllb Rllb Conference Status Report Control 14-1 ItcsImcu Multi-point Conference Status Report Control 14-2 I243 Report Control 14-3 Command Generator Related Report Control 14-4Icgp Cram IsprRrst Checking System Clock Setting 15-5 Setting System Clock 15-4Wclk Rclk Rmna Mutli-point Conference Status CommandXxxxxxxx Rmst Rmps Read Multi-point Conference Mode Status 16-4Read Multi-point Conference Operation Status 16-3 Rmmd Read Model Identification 17-1 RmesRmes Ects Audio Training Command 18-1Ects Requesting Connection 19-1 Ncrn Requesting Disconnection 19-2 NdscNcic Incoming Call Permit/Reject 19-3 Communication Status Inquiry 19-4 NstqNstq Request for Camera Direction Change 20-1 Cams Pointer Control 21-1 PocsVcts Talker Detection Control 21-2 Stpr Standard Display Screen Setting Request 21-4SnapShot Transmission Request 21-3 Sxmr Sxst Request to Acquire Composite Screen Setting 21-5 Request to Chairman Control 22-1 Copr Multiple Address Transmission Request 22-2 Cspr Crpr Request to Switch Multiple Address Originator Monitor 22-4Specific Picture Reception Request 22-3 Cmpr Omes Opening Control CommandOpening Message at Unit Activation 23-1 Imac H221 Synchronous Status Report 24-1Manufacturer Code Report 24-2 Imod Report of Common Mode in Communication 24-3ON/OFF LSD Speed CPU/ Video alarm Alarm Status Change Report 1 25-1Ralm Alarm Status Change Report 2 25-1 Incoming Video Synchronous Status Report 26-1 Rvsr Participating Conference Status Report 27-1 Icst Ninc NaltNonl Disconnection Report 28-4 Ndci Camera Status Report 29-1 CamiCpni Talker Name Display Report 29-2 SnapShot Transmission Ending Report 30-1 SteiRfvr SnapShot Reception Report 30-2 Automatic Activation File Starting Report 31-1 CgsiCgei Automatic Activating File Ending Report 31-2 Immd ImpsCopi Crpi CspiCvci SnapShot Transmission Permit Report 32-7 CsscCmpi Cjni Conference Status Report 32-10 Csti Standard Display Screen Setting Report 33-2 Composite Screen Setting Report 33-1Xmii Xmci Xsci Response to Composite Screen Setting Request 33-3 Voice Activate Microphone Report 34-1 Ppni Erri System Error Report 35-1 On-Screen Command Setting On-Screen Display 36-1Sosd Cstb Current Power OFF Condition 37-1Cstb This page is for your notes Error Response /2 Error Response Table Error Response Table VisuaLink 128/384 Engineering Guide List of Factors for Disconnection in Table Factors Disconnections VisuaLink 128/384 Engineering Guide Factors Disconnections Factors of Disconnections MIC Connection 1 Headset Telephone Connection Line Isdn ConnectionVideo Socket Input/Output 2B 128kbps Line Speed 1B 64kbps Line Speed Appendix B VisuaLink 128/384 Engineering Guide Table C Isdn Q.931 Cause Code Definitions Appendix C Isdn Q.931 Cause Code Definitions Appendix CVisuaLink 128/384 Engineering Guide NDA-24233 Issue C-3 Appendix C VisuaLink 128/384 Engineering Guide